lkml.org 
[lkml]   [2021]   [May]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/5] dt-bindings: mfd: Binding for RTL8231
On Tue, May 11, 2021 at 02:25:20PM +0200, Sander Vanheule wrote:
> Add a binding description for the Realtek RTL8231, a GPIO and LED
> expander chip commonly used in ethernet switches based on a Realtek
> switch SoC. These chips can be addressed via an MDIO or SMI bus, or used
> as a plain 36-bit shift register.
>
> This binding only describes the feature set provided by the MDIO/SMI
> configuration, and covers the GPIO, PWM, and pin control properties. The
> LED properties are defined in a separate binding.
>
> Signed-off-by: Sander Vanheule <sander@svanheule.net>
> ---
> .../bindings/mfd/realtek,rtl8231.yaml | 202 ++++++++++++++++++
> 1 file changed, 202 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml b/Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
> new file mode 100644
> index 000000000000..2023cfa887a3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
> @@ -0,0 +1,202 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/realtek,rtl8231.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Realtek RTL8231 GPIO and LED expander.
> +
> +maintainers:
> + - Sander Vanheule <sander@svanheule.net>
> +
> +description: |
> + The RTL8231 is a GPIO and LED expander chip, providing up to 37 GPIOs, up to
> + 88 LEDs, and up to one PWM output. This device is frequently used alongside
> + Realtek switch SoCs, to provide additional I/O capabilities.
> +
> + To manage the RTL8231's features, its strapping pins can be used to configure
> + it in one of three modes: shift register, MDIO device, or SMI device. The
> + shift register mode does not need special support. In MDIO or SMI mode, most
> + pins can be configured as a GPIO output, LED matrix scan line/column, or as a
> + PWM output.
> +
> + The GPIO and pin control are part of the main node. PWM and LED support are
> + configured as sub-nodes.
> +
> +properties:
> + compatible:
> + const: realtek,rtl8231
> +
> + reg:
> + description: MDIO or SMI device address.
> + maxItems: 1
> +
> + # GPIO support
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> + description: |
> + The first cell is the pin number and the second cell is used to specify
> + the gpio active state.
> +
> + gpio-ranges:
> + description: |
> + Must reference itself, and provide a zero-based mapping for 37 pins.
> + maxItems: 1
> +
> + # Pin muxing and configuration
> + realtek,drive-strength:
> + $ref: /schemas/types.yaml#/definitions/uint32

Use the standard 'drive-strength' property.

> + description: |
> + Common drive strength used for all GPIO output pins, must be 4mA or 8mA.
> + On reset, this value will default to 8mA.
> + enum: [4, 8]
> +
> + # LED scanning matrix
> + leds:
> + $ref: ../leds/realtek,rtl8231-leds.yaml#
> +
> + # PWM output
> + pwm:
> + type: object
> + description: |
> + Subnode describing the PWM peripheral. To use the PWM output, gpio35 must
> + be muxed to its 'pwm' function. Valid frequency values for consumers are
> + 1200, 1600, 2000, 2400, 2800, 3200, 4000, and 4800.
> +
> + properties:
> + "#pwm-cells":
> + description: |
> + Twos cells with PWM index (must be 0) and PWM frequency in Hz.
> + const: 2
> +
> + required:
> + - "#pwm-cells"

Just move this to the parent node. No reason for a child node or that 1
node can't be 2 providers.

> +
> +patternProperties:
> + "-pins$":
> + type: object
> + $ref: ../pinctrl/pinmux-node.yaml#
> +
> + properties:
> + pins:
> + items:
> + oneOf:

No need for oneOf when there's only 1 entry.

> + - enum: ["gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6",
> + "gpio7", "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13",
> + "gpio14", "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20",
> + "gpio21", "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27",
> + "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34",
> + "gpio35", "gpio36"]
> + minItems: 1
> + maxItems: 37
> + function:
> + description: |
> + Select which function to use. "gpio" is supported for all pins, "led" is supported
> + for pins 0-34, "pwm" is supported for for pin 35.
> + enum: ["gpio", "led", "pwm"]
> +
> + required:
> + - pins
> + - function
> +
> +required:
> + - compatible
> + - reg
> + - gpio-controller
> + - "#gpio-cells"
> + - gpio-ranges
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + // Minimal example
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + expander0: expander@0 {
> + compatible = "realtek,rtl8231";
> + reg = <0>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&expander0 0 0 37>;
> + };
> + };
> + - |
> + // All bells and whistles included
> + #include <dt-bindings/leds/common.h>
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + expander1: expander@1 {
> + compatible = "realtek,rtl8231";
> + reg = <1>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&expander1 0 0 37>;
> +
> + realtek,drive-strength = <4>;
> +
> + button-pins {
> + pins = "gpio36";
> + function = "gpio";
> + input-debounce = "100000";
> + };
> +
> + pwm-pins {
> + pins = "gpio35";
> + function = "pwm";
> + };
> +
> + led-pins {
> + pins = "gpio0", "gpio1", "gpio3", "gpio4";
> + function = "led";
> + };
> +
> + pwm {
> + #pwm-cells = <2>;
> + };
> +
> + leds {
> + compatible = "realtek,rtl8231-leds";
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + realtek,led-scan-mode = "single-color";
> +
> + led@0,0 {
> + reg = <0 0>;
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <0>;
> + };
> +
> + led@0,1 {
> + reg = <0 1>;
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <0>;
> + };
> +
> + led@1,0 {
> + reg = <1 0>;
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <1>;
> + };
> +
> + led@1,1 {
> + reg = <1 1>;
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <1>;
> + };
> + };
> + };
> + };
> --
> 2.31.1
>

\
 
 \ /
  Last update: 2021-05-18 00:39    [W:1.495 / U:0.680 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site