lkml.org 
[lkml]   [2021]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v4 0/5] RTL8231 GPIO expander support
Date
The RTL8231 GPIO and LED expander can be configured for use as an MDIO or SMI
bus device. Currently only the MDIO mode is supported, although SMI mode
support should be fairly straightforward, once an SMI bus driver is available.

Provided features by the RTL8231:
- Up to 37 GPIOs
- Configurable drive strength: 8mA or 4mA (currently unsupported)
- Input debouncing on high GPIOs (currently unsupported)
- Up to 88 LEDs in multiple scan matrix groups
- On, off, or one of six toggling intervals
- "single-color mode": 2×36 single color LEDs + 8 bi-color LEDs
- "bi-color mode": (12 + 2×6) bi-color LEDs + 24 single color LEDs
- Up to one PWM output (currently unsupported)
- Fixed duty cycle, 8 selectable frequencies (1.2kHz - 4.8kHz)

The GPIO controller uses gpio-regmap. The assumed read-modify-write behaviour
of the data output is provided by using a cached virtual address range for the
output values.

Register access is provided through a new MDIO regmap provider. The required
MDIO regmap support was merged in Mark Brown's regmap repository, and can be
found under the regmap-mdio tag:
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git/tag/?h=regmap-mdio

Changes since v3:
- Drop gpio-regmap direction-before-value quirk
- Use secondary virtual register range to enable proper read-modify-write
behaviour on GPIO output values
- Add pin debounce support
- Switch to generic pinmux functions

Changes since v2:
- MDIO regmap support was merged, so patch is dropped here
- Implement feedback for DT bindings
- Use correct module names in Kconfigs
- Fix k*alloc return value checks
- Introduce GPIO regmap quirks to set output direction first
- pinctrl: Use static pin descriptions for pin controller
- pinctrl: Fix gpio consumer resource leak
- mfd: Replace CONFIG_PM-ifdef'ery
- leds: Rename interval to interval_ms

Changes since v1:
- Reintroduce MDIO regmap, with fixed Kconfig dependencies
- Add configurable dir/value order for gpio-regmap direction_out call
- Drop allocations for regmap fields that are used only on init
- Move some definitions to MFD header
- Add PM ops to replace driver remove for MFD
- Change pinctrl driver to (modified) gpio-regmap
- Change leds driver to use fwnode

Changes since RFC:
- Dropped MDIO regmap interface. I was unable to resolve the Kconfig
dependency issue, so have reverted to using regmap_config.reg_read/write.
- Added pinctrl support
- Added LED support
- Changed root device to MFD, with pinctrl and leds child devices. Root
device is now an mdio_device driver.

Sander Vanheule (5):
dt-bindings: leds: Binding for RTL8231 scan matrix
dt-bindings: mfd: Binding for RTL8231
mfd: Add RTL8231 core device
pinctrl: Add RTL8231 pin control and GPIO support
leds: Add support for RTL8231 LED scan matrix

.../bindings/leds/realtek,rtl8231-leds.yaml | 166 +++++++
.../bindings/mfd/realtek,rtl8231.yaml | 190 ++++++++
drivers/leds/Kconfig | 10 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-rtl8231.c | 291 ++++++++++++
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rtl8231.c | 240 ++++++++++
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-rtl8231.c | 438 ++++++++++++++++++
include/linux/mfd/rtl8231.h | 78 ++++
12 files changed, 1436 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/realtek,rtl8231-leds.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
create mode 100644 drivers/leds/leds-rtl8231.c
create mode 100644 drivers/mfd/rtl8231.c
create mode 100644 drivers/pinctrl/pinctrl-rtl8231.c
create mode 100644 include/linux/mfd/rtl8231.h

--
2.31.1

\
 
 \ /
  Last update: 2021-06-03 12:01    [W:0.349 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site