lkml.org 
[lkml]   [2022]   [Mar]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC 00/10] add support for fwnode in i2c mux system and sfp
Le Thu, 24 Feb 2022 15:40:40 +0100,
Clément Léger <clement.leger@bootlin.com> a écrit :

> Hi,
>
> As stated at the beginning of the cover letter, the PCIe card I'm
> working on uses a lan9662 SoC. This card is meant to be used an
> ethernet switch with 2 x RJ45 ports and 2 x 10G SFPs. The lan966x SoCs
> can be used in two different ways:
>
> - It can run Linux by itself, on ARM64 cores included in the SoC. This
> use-case of the lan966x is currently being upstreamed, using a
> traditional Device Tree representation of the lan996x HW blocks [1]
> A number of drivers for the different IPs of the SoC have already
> been merged in upstream Linux.
>
> - It can be used as a PCIe endpoint, connected to a separate platform
> that acts as the PCIe root complex. In this case, all the devices
> that are embedded on this SoC are exposed through PCIe BARs and the
> ARM64 cores of the SoC are not used. Since this is a PCIe card, it
> can be plugged on any platform, of any architecture supporting PCIe.
>
> The goal of this effort is to enable this second use-case, while
> allowing the re-use of the existing drivers for the different devices
> part of the SoC.
>
> Following a first round of discussion, here are some clarifications on
> what problem this series is trying to solve and what are the possible
> choices to support this use-case.
>
> Here is the list of devices that are exposed and needed to make this
> card work as an ethernet switch:
> - lan966x-switch
> - reset-microchip-sparx5
> - lan966x_serdes
> - reset-microchip-lan966x-phy
> - mdio-mscc-miim
> - pinctrl-lan966x
> - atmel-flexcom
> - i2c-at91
> - i2c-mux
> - i2c-mux-pinctrl
> - sfp
> - clk-lan966x
>
> All the devices on this card are "self-contained" and do not require
> cross-links with devices that are on the host (except to demux IRQ but
> this is something easy to do). These drivers already exists and are
> using of_* API to register controllers, get properties and so on.
>
> The challenge we're trying to solve is how can the PCI driver for this
> card re-use the existing drivers, and using which hardware
> representation to instantiate all those drivers.
>
> Although this series only contained the modifications for the I2C
> subsystem all the subsystems that are used or needed by the previously
> listed driver have also been modified to have support for fwnode. This
> includes the following subsystems:
> - reset
> - clk
> - pinctrl
> - syscon
> - gpio
> - pinctrl
> - phy
> - mdio
> - i2c
>
> The first feedback on this series does not seems to reach a consensus
> (to say the least) on how to do it cleanly so here is a recap of the
> possible solutions, either brought by this series or mentioned by
> contributors:
>
> 1) Describe the card statically using swnode
>
> This is the approach that was taken by this series. The devices are
> described using the MFD subsystem with mfd_cells. These cells are
> attached with a swnode which will be used as a primary node in place of
> ACPI or OF description. This means that the device description
> (properties and references) is conveyed entirely in the swnode. In order
> to make these swnode usable with existing OF based subsystems, the
> fwnode API can be used in needed subsystems.
>
> Pros:
> - Self-contained in the driver.
> - Will work on all platforms no matter the firmware description.
> - Makes the subsystems less OF-centric.
>
> Cons:
> - Modifications are required in subsystems to support fwnode
> (mitigated by the fact it makes to subsystems less OF-centric).
> - swnode are not meant to be used entirely as primary nodes.
> - Specifications for both ACPI and OF must be handled if using fwnode
> API.
>
> 2) Use SSDT overlays
>
> Andy mentioned that SSDT overlays could be used. This overlay should
> match the exact configuration that is used (ie correct PCIe bus/port
> etc). It requires the user to write/modify/compile a .asl file and load
> it using either EFI vars, custom initrd or via configfs. The existing
> drivers would also need more modifications to work with ACPI. Some of
> them might even be harder (if not possible) to use since there is no
> ACPI support for the subsystems they are using .
>
> Pros:
> - Can't really find any for this one
>
> Cons:
> - Not all needed subsystems have appropriate ACPI bindings/support
> (reset, clk, pinctrl, syscon).
> - Difficult to setup for the user (modify/compile/load .aml file).
> - Not portable between machines, as the SSDT overlay need to be
> different depending on how the PCI device is connected to the
> platform.
>
> 3) Use device-tree overlays
>
> This solution was proposed by Andrew and could potentially allows to
> keep all the existing device-tree infrastructure and helpers. A
> device-tree overlay could be loaded by the driver and applied using
> of_overlay_fdt_apply(). There is some glue to make this work but it
> could potentially be possible. Mark have raised some warnings about
> using such device-tree overlays on an ACPI enabled platform.
>
> Pros:
> - Reuse all the existing OF infrastructure, no modifications at all on
> drivers and subsystems.
> - Could potentially lead to designing a generic driver for PCI devices
> that uses a composition of other drivers.
>
> Cons:
> - Might not the best idea to mix it with ACPI.
> - Needs CONFIG_OF, which typically isn't enabled today on most x86
> platforms.
> - Loading DT overlays on non-DT platforms is not currently working. It
> can be addressed, but it's not necessarily immediate.
>
> My preferred solutions would be swnode or device-tree overlays but
> since there to is no consensus on how to add this support, how
> can we go on with this series ?
>
> Thanks,
>
> [1]
> https://lore.kernel.org/linux-arm-kernel/20220210123704.477826-1-michael@walle.cc/
>

Does anybody have some other advices or recommendation regarding
this RFC ? It would be nice to have more feedback on the solution that
might e preferred to support this use-case.

Thanks,


--
Clément Léger,
Embedded Linux and Kernel engineer at Bootlin
https://bootlin.com

\
 
 \ /
  Last update: 2022-03-08 11:49    [W:0.445 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site