lkml.org 
[lkml]   [2022]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v3 0/4] Watchdog: sp5100_tco: Replace cd6h/cd7h port I/O accesses with MMIO accesses
Date
This driver uses cd6h/cd7h port I/O to access the FCH::PM::DECODEEN and
FCH::PM::ISACONTROL registers during driver initialization. cd6h/cd7h port
I/O is no longer supported on later AMD processors and the recommended
method to access these registers is using MMIO. This series will replace
the cd6h/cd7h port I/O with MMIO accesses during initialization.

The first patch refactors watchdog timer initialization into a separate
function. This is needed to add support for new device layouts without
adding complexity.

The second patch moves region request/release into new functions. The
request/release functions provide a location for adding MMIO region
support.

The third patch introduces EFCH initialization using MMIO. This is
required because the registers are no longer accessible using cd6h/cd7h
port I/O.

The fourth patch adds SMBus controller PCI ID check to enable EFCH MMIO
initialization. This eliminates the need for driver updates to support
future processors supporting the same EFCH functionality.

Important:
This series includes patches with MMIO accesses to registers
FCH::PM::DECODEEN and FCH::PM::ISACONTROL. The same registers are also
accessed by the piix4_smbus driver. The registers are currently accessed
indirectly through cd6h/cd7h port I/O and both drivers use
request_muxed_region() to synchronize the accesses. It should be noted the
request_muxed_region() uses a wait queue to sleep and retry taking
exclusive access if the port I/O region is busy.

This series uses request_mem_region() to synchronize accesses to the MMIO
registers mentioned above. request_mem_region() is missing the retry
logic in the case the resource is busy. As a result, request_mem_region()
will fail immediately if the resource is busy. The 'muxed' variant is
needed here but request_muxed_mem_region() is not defined to use. I will
follow up with another patch series to define the
request_muxed_mem_region() and use in both drivers.

The piix4_smbus driver or the sp5100_tco driver can potentialy fail until
the muxed mem synchronization series is present in the tree. The potential
for failure is not likely because the sp5100_tco driver only accesses the
FCH::PM::DECODEEN and FCH::PM::ISACONTROL registers during driver
initialization.

Link: https://lore.kernel.org/all/20210715221828.244536-1-Terry.Bowman@amd.com/#t

Based on v5.16

Testing:
Tested on AMD family 17h and family 19h processors using:

cat >> /dev/watchdog

Changes in V3:
- Remove 'addr' and 'res' variables from struct sp5100_tco.
(Guenter Roeck)
- Pass address directly to efch_read_pm_reg8() and
efch_update_pm_reg8(). (Guenter Roeck)
- Reword patch descriptions. (Terry Bowman)
- Change #define AMD_ZEN_SMBUS_PCI_REV value from 0x59 to 0x51. This was
determined after investigating programmers manual and testing.
(Robert Richter)
- Refactor efch_* functions() (Robert Richter)
- Remove trailing whitespace in patch. (Guenter Roeck)

Terry Bowman (4):
Watchdog: sp5100_tco: Move timer initialization into function
Watchdog: sp5100_tco: Refactor MMIO base address initialization
Watchdog: sp5100_tco: Add initialization using EFCH MMIO
Watchdog: sp5100_tco: Enable Family 17h+ CPUs

drivers/watchdog/sp5100_tco.c | 335 ++++++++++++++++++++++------------
drivers/watchdog/sp5100_tco.h | 6 +
2 files changed, 227 insertions(+), 114 deletions(-)

--
2.30.2

\
 
 \ /
  Last update: 2022-01-18 21:23    [W:0.261 / U:2.768 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site