lkml.org 
[lkml]   [2021]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 10/13] dt-bindings: spi: cadence-qspi: Add support for Pensando Elba SoC
Hi Brad,

On 28/03/21 06:59PM, Brad Larson wrote:
> Add new vendor Pensando Systems Elba SoC compatible
> string and convert to json-schema.
>
> Signed-off-by: Brad Larson <brad@pensando.io>
> ---
> .../bindings/spi/cadence-quadspi.txt | 68 --------
> .../bindings/spi/cadence-quadspi.yaml | 153 ++++++++++++++++++
> 2 files changed, 153 insertions(+), 68 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> deleted file mode 100644
> index 8ace832a2d80..000000000000
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,68 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> - Generic default - "cdns,qspi-nor".
> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> - For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> - physical address and length. The first entry is the address and
> - length of the controller register set. The second entry is the
> - address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> - the read data rather than the QSPI clock. Make sure that QSPI return
> - clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> - mode chip select outputs are de-asserted between
> - transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> - de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> - transaction and deasserting the device chip select
> - (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> - and first bit transfer.
> -- resets : Must contain an entry for each entry in reset-names.
> - See ../reset/reset.txt for details.
> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> - qspi: spi@ff705000 {
> - compatible = "cdns,qspi-nor";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0xff705000 0x1000>,
> - <0xffa00000 0x1000>;
> - interrupts = <0 151 4>;
> - clocks = <&qspi_clk>;
> - cdns,is-decoded-cs;
> - cdns,fifo-depth = <128>;
> - cdns,fifo-width = <4>;
> - cdns,trigger-address = <0x00000000>;
> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> - reset-names = "qspi", "qspi-ocp";
> -
> - flash0: n25q00@0 {
> - ...
> - cdns,read-delay = <4>;
> - cdns,tshsl-ns = <50>;
> - cdns,tsd2d-ns = <50>;
> - cdns,tchsh-ns = <4>;
> - cdns,tslch-ns = <4>;
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> new file mode 100644
> index 000000000000..94d631045153
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> @@ -0,0 +1,153 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Cadence Quad SPI controller
> +
> +maintainers:
> + - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> + - Brad Larson <brad@pensando.io>
> +
> +properties:
> + compatible:
> + contains:
> + enum:
> + - cdns,qspi-nor # Generic default
> + - ti,k2g-qspi # TI 66AK2G SoC
> + - ti,am654-ospi # TI AM654 SoC
> + - intel,lgm-qspi # Intel LGM SoC
> + - pensando,cdns-qspi # Pensando Elba SoC

Wouldn't this allow any combination of all 5 strings? So for example
this would allow "ti,am654-ospi", "pensando,cdns-qspi" which is
obviously not correct.

I sent a patch recently [0] that does this correctly and it has gotten
Rob's blessing. So I suggest you build your patch on top of that.

[...]

[0] https://patchwork.kernel.org/project/spi-devel-general/patch/20210326130034.15231-5-p.yadav@ti.com/

--
Regards,
Pratyush Yadav
Texas Instruments Inc.

\
 
 \ /
  Last update: 2021-03-30 13:14    [W:0.220 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site