lkml.org 
[lkml]   [2021]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v11 1/9] drivers: thermal: tsens: Add VER_0 tsens version
Date


On 3/18/21 8:52 PM, Ansuel Smith wrote:
> VER_0 is used to describe device based on tsens version before v0.1.
> These device are devices based on msm8960 for example apq8064 or
> ipq806x.

Hi Ansuel,

There are still checkpatch check warnings in this patch. Please run
checkpatch.pl --strict and fix them. Once that is done, you can add

Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>

Warm Regards
Thara

>
> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> ---
> drivers/thermal/qcom/tsens.c | 141 ++++++++++++++++++++++++++++-------
> drivers/thermal/qcom/tsens.h | 4 +-
> 2 files changed, 116 insertions(+), 29 deletions(-)
>
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index d8ce3a687b80..277d9b17e949 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -12,6 +12,7 @@
> #include <linux/of.h>
> #include <linux/of_address.h>
> #include <linux/of_platform.h>
> +#include <linux/mfd/syscon.h>
> #include <linux/platform_device.h>
> #include <linux/pm.h>
> #include <linux/regmap.h>
> @@ -515,6 +516,15 @@ static irqreturn_t tsens_irq_thread(int irq, void *data)
> dev_dbg(priv->dev, "[%u] %s: no violation: %d\n",
> hw_id, __func__, temp);
> }
> +
> + if (tsens_version(priv) < VER_0_1) {
> + /* Constraint: There is only 1 interrupt control register for all
> + * 11 temperature sensor. So monitoring more than 1 sensor based
> + * on interrupts will yield inconsistent result. To overcome this
> + * issue we will monitor only sensor 0 which is the master sensor.
> + */
> + break;
> + }
> }
>
> return IRQ_HANDLED;
> @@ -530,6 +540,13 @@ static int tsens_set_trips(void *_sensor, int low, int high)
> int high_val, low_val, cl_high, cl_low;
> u32 hw_id = s->hw_id;
>
> + if (tsens_version(priv) < VER_0_1) {
> + /* Pre v0.1 IP had a single register for each type of interrupt
> + * and thresholds
> + */
> + hw_id = 0;
> + }
> +
> dev_dbg(dev, "[%u] %s: proposed thresholds: (%d:%d)\n",
> hw_id, __func__, low, high);
>
> @@ -584,18 +601,21 @@ int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp)
> u32 valid;
> int ret;
>
> - ret = regmap_field_read(priv->rf[valid_idx], &valid);
> - if (ret)
> - return ret;
> - while (!valid) {
> - /* Valid bit is 0 for 6 AHB clock cycles.
> - * At 19.2MHz, 1 AHB clock is ~60ns.
> - * We should enter this loop very, very rarely.
> - */
> - ndelay(400);
> + /* VER_0 doesn't have VALID bit */
> + if (tsens_version(priv) >= VER_0_1) {
> ret = regmap_field_read(priv->rf[valid_idx], &valid);
> if (ret)
> return ret;
> + while (!valid) {
> + /* Valid bit is 0 for 6 AHB clock cycles.
> + * At 19.2MHz, 1 AHB clock is ~60ns.
> + * We should enter this loop very, very rarely.
> + */
> + ndelay(400);
> + ret = regmap_field_read(priv->rf[valid_idx], &valid);
> + if (ret)
> + return ret;
> + }
> }
>
> /* Valid bit is set, OK to read the temperature */
> @@ -608,15 +628,29 @@ int get_temp_common(const struct tsens_sensor *s, int *temp)
> {
> struct tsens_priv *priv = s->priv;
> int hw_id = s->hw_id;
> - int last_temp = 0, ret;
> + int last_temp = 0, ret, trdy;
> + unsigned long timeout;
>
> - ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
> - if (ret)
> - return ret;
> + timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
> + do {
> + if (tsens_version(priv) == VER_0) {
> + ret = regmap_field_read(priv->rf[TRDY], &trdy);
> + if (ret)
> + return ret;
> + if (!trdy)
> + continue;
> + }
>
> - *temp = code_to_degc(last_temp, s) * 1000;
> + ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp);
> + if (ret)
> + return ret;
>
> - return 0;
> + *temp = code_to_degc(last_temp, s) * 1000;
> +
> + return 0;
> + } while (time_before(jiffies, timeout));
> +
> + return -ETIMEDOUT;
> }
>
> #ifdef CONFIG_DEBUG_FS
> @@ -738,19 +772,31 @@ int __init init_common(struct tsens_priv *priv)
> priv->tm_offset = 0x1000;
> }
>
> - res = platform_get_resource(op, IORESOURCE_MEM, 0);
> - tm_base = devm_ioremap_resource(dev, res);
> - if (IS_ERR(tm_base)) {
> - ret = PTR_ERR(tm_base);
> - goto err_put_device;
> + if (tsens_version(priv) >= VER_0_1) {
> + res = platform_get_resource(op, IORESOURCE_MEM, 0);
> + tm_base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(tm_base)) {
> + ret = PTR_ERR(tm_base);
> + goto err_put_device;
> + }
> +
> + priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
> + } else { /* VER_0 share the same gcc regs using a syscon */
> + struct device *parent = priv->dev->parent;
> +
> + if (parent)
> + priv->tm_map = syscon_node_to_regmap(parent->of_node);
> }
>
> - priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config);
> - if (IS_ERR(priv->tm_map)) {
> + if (IS_ERR_OR_NULL(priv->tm_map)) {
> ret = PTR_ERR(priv->tm_map);
> goto err_put_device;
> }
>
> + /* VER_0 have only tm_map */
> + if (!priv->srot_map)
> + priv->srot_map = priv->tm_map;
> +
> if (tsens_version(priv) > VER_0_1) {
> for (i = VER_MAJOR; i <= VER_STEP; i++) {
> priv->rf[i] = devm_regmap_field_alloc(dev, priv->srot_map,
> @@ -769,6 +815,10 @@ int __init init_common(struct tsens_priv *priv)
> ret = PTR_ERR(priv->rf[TSENS_EN]);
> goto err_put_device;
> }
> + /* in VER_0 TSENS need to be explicitly enabled */
> + if (tsens_version(priv) == VER_0)
> + regmap_field_write(priv->rf[TSENS_EN], 1);
> +
> ret = regmap_field_read(priv->rf[TSENS_EN], &enabled);
> if (ret)
> goto err_put_device;
> @@ -791,6 +841,20 @@ int __init init_common(struct tsens_priv *priv)
> goto err_put_device;
> }
>
> + priv->rf[TSENS_SW_RST] = devm_regmap_field_alloc(
> + dev, priv->srot_map, priv->fields[TSENS_SW_RST]);
> + if (IS_ERR(priv->rf[TSENS_SW_RST])) {
> + ret = PTR_ERR(priv->rf[TSENS_SW_RST]);
> + goto err_put_device;
> + }
> +
> + priv->rf[TRDY] =
> + devm_regmap_field_alloc(dev, priv->tm_map, priv->fields[TRDY]);
> + if (IS_ERR(priv->rf[TRDY])) {
> + ret = PTR_ERR(priv->rf[TRDY]);
> + goto err_put_device;
> + }
> +
> /* This loop might need changes if enum regfield_ids is reordered */
> for (j = LAST_TEMP_0; j <= UP_THRESH_15; j += 16) {
> for (i = 0; i < priv->feat->max_sensors; i++) {
> @@ -806,7 +870,7 @@ int __init init_common(struct tsens_priv *priv)
> }
> }
>
> - if (priv->feat->crit_int) {
> + if (priv->feat->crit_int || tsens_version(priv) < VER_0_1) {
> /* Loop might need changes if enum regfield_ids is reordered */
> for (j = CRITICAL_STATUS_0; j <= CRIT_THRESH_15; j += 16) {
> for (i = 0; i < priv->feat->max_sensors; i++) {
> @@ -844,7 +908,11 @@ int __init init_common(struct tsens_priv *priv)
> }
>
> spin_lock_init(&priv->ul_lock);
> - tsens_enable_irq(priv);
> +
> + /* VER_0 interrupt doesn't need to be enabled */
> + if (tsens_version(priv) >= VER_0_1)
> + tsens_enable_irq(priv);
> +
> tsens_debug_init(op);
>
> err_put_device:
> @@ -943,10 +1011,14 @@ static int tsens_register_irq(struct tsens_priv *priv, char *irqname,
> if (irq == -ENXIO)
> ret = 0;
> } else {
> - ret = devm_request_threaded_irq(&pdev->dev, irq,
> - NULL, thread_fn,
> - IRQF_ONESHOT,
> - dev_name(&pdev->dev), priv);
> + /* VER_0 interrupt is TRIGGER_RISING, VER_0_1 and up is ONESHOT */
> + ret = devm_request_threaded_irq(
> + &pdev->dev, irq,
> + tsens_version(priv) == VER_0 ? thread_fn : NULL,
> + tsens_version(priv) == VER_0 ? NULL : thread_fn,
> + tsens_version(priv) == VER_0 ? IRQF_TRIGGER_RISING :
> + IRQF_ONESHOT,
> + dev_name(&pdev->dev), priv);
> if (ret)
> dev_err(&pdev->dev, "%s: failed to get irq\n",
> __func__);
> @@ -975,6 +1047,19 @@ static int tsens_register(struct tsens_priv *priv)
> priv->ops->enable(priv, i);
> }
>
> + /* VER_0 require to set MIN and MAX THRESH
> + * These 2 regs are set using the:
> + * - CRIT_THRESH_0 for MAX THRESH hardcoded to 120°C
> + * - CRIT_THRESH_1 for MIN THRESH hardcoded to 0°C
> + */
> + if (tsens_version(priv) < VER_0_1) {
> + regmap_field_write(priv->rf[CRIT_THRESH_0],
> + tsens_mC_to_hw(priv->sensor, 120000));
> +
> + regmap_field_write(priv->rf[CRIT_THRESH_1],
> + tsens_mC_to_hw(priv->sensor, 0));
> + }
> +
> ret = tsens_register_irq(priv, "uplow", tsens_irq_thread);
> if (ret < 0)
> return ret;
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index f40b625f897e..8e6c1fd3ccf5 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -13,6 +13,7 @@
> #define CAL_DEGC_PT2 120
> #define SLOPE_FACTOR 1000
> #define SLOPE_DEFAULT 3200
> +#define TIMEOUT_US 100
> #define THRESHOLD_MAX_ADC_CODE 0x3ff
> #define THRESHOLD_MIN_ADC_CODE 0x0
>
> @@ -25,7 +26,8 @@ struct tsens_priv;
>
> /* IP version numbers in ascending order */
> enum tsens_ver {
> - VER_0_1 = 0,
> + VER_0 = 0,
> + VER_0_1,
> VER_1_X,
> VER_2_X,
> };
>

\
 
 \ /
  Last update: 2021-03-19 14:12    [W:0.142 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site