lkml.org 
[lkml]   [2021]   [Nov]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH v2 11/20] power: supply: bq25890: Add support for registering the Vbus boost converter as a regulator
On Sun, Nov 14, 2021 at 7:04 PM Hans de Goede <hdegoede@redhat.com> wrote:
>
> The bq25890_charger code supports enabling/disabling the boost converter
> based on usb-phy notifications. But the usb-phy framework is not used on
> all boards/platforms. At support for registering the Vbus boost converter
> as a standard regulator when there is no usb-phy on the board.
>
> Also add support for providing regulator_init_data through platform_data
> for use on boards where device-tree is not used and the platform code must
> thus provide the regulator_init_data.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

One remark below.

> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v2:
> - When the usb-phy framework is not used, turn off the Vboost regulator
> on shutdown
> - Some minor code-tweaks based on Andy's review
> ---
> drivers/power/supply/bq25890_charger.c | 80 ++++++++++++++++++++++++++
> include/linux/power/bq25890_charger.h | 15 +++++
> 2 files changed, 95 insertions(+)
> create mode 100644 include/linux/power/bq25890_charger.h
>
> diff --git a/drivers/power/supply/bq25890_charger.c b/drivers/power/supply/bq25890_charger.c
> index 3c41fe86b3d3..e06ca7b0eb3e 100644
> --- a/drivers/power/supply/bq25890_charger.c
> +++ b/drivers/power/supply/bq25890_charger.c
> @@ -8,7 +8,9 @@
> #include <linux/module.h>
> #include <linux/i2c.h>
> #include <linux/power_supply.h>
> +#include <linux/power/bq25890_charger.h>
> #include <linux/regmap.h>
> +#include <linux/regulator/driver.h>
> #include <linux/types.h>
> #include <linux/gpio/consumer.h>
> #include <linux/interrupt.h>
> @@ -845,6 +847,45 @@ static int bq25890_usb_notifier(struct notifier_block *nb, unsigned long val,
> return NOTIFY_OK;
> }
>
> +#ifdef CONFIG_REGULATOR
> +static int bq25890_vbus_enable(struct regulator_dev *rdev)
> +{
> + struct bq25890_device *bq = rdev_get_drvdata(rdev);
> +
> + return bq25890_set_otg_cfg(bq, 1);
> +}
> +
> +static int bq25890_vbus_disable(struct regulator_dev *rdev)
> +{
> + struct bq25890_device *bq = rdev_get_drvdata(rdev);
> +
> + return bq25890_set_otg_cfg(bq, 0);
> +}
> +
> +static int bq25890_vbus_is_enabled(struct regulator_dev *rdev)
> +{
> + struct bq25890_device *bq = rdev_get_drvdata(rdev);
> +
> + return bq25890_field_read(bq, F_OTG_CFG);
> +}
> +
> +static const struct regulator_ops bq25890_vbus_ops = {
> + .enable = bq25890_vbus_enable,
> + .disable = bq25890_vbus_disable,
> + .is_enabled = bq25890_vbus_is_enabled,
> +};
> +
> +static const struct regulator_desc bq25890_vbus_desc = {
> + .name = "usb_otg_vbus",
> + .of_match = "usb-otg-vbus",
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> + .ops = &bq25890_vbus_ops,
> + .fixed_uV = 5000000,
> + .n_voltages = 1,
> +};
> +#endif
> +
> static int bq25890_get_chip_version(struct bq25890_device *bq)
> {
> int id, rev;
> @@ -1044,6 +1085,22 @@ static int bq25890_probe(struct i2c_client *client,
> bq->usb_nb.notifier_call = bq25890_usb_notifier;
> usb_register_notifier(bq->usb_phy, &bq->usb_nb);
> }
> +#ifdef CONFIG_REGULATOR
> + else {
> + struct bq25890_platform_data *pdata = dev_get_platdata(dev);
> + struct regulator_config cfg = { };
> + struct regulator_dev *reg;
> +
> + cfg.dev = dev;
> + cfg.driver_data = bq;
> + if (pdata)
> + cfg.init_data = pdata->regulator_init_data;
> +
> + reg = devm_regulator_register(dev, &bq25890_vbus_desc, &cfg);
> + if (IS_ERR(reg))
> + return dev_err_probe(dev, PTR_ERR(reg), "registering regulator");
> + }
> +#endif

I just realized that you may use even

} else {
#ifdef
...
#endif
}

w/o any compiler warning or so. But it's up to you.

> ret = bq25890_power_supply_init(bq);
> if (ret < 0) {
> @@ -1082,6 +1139,28 @@ static int bq25890_remove(struct i2c_client *client)
> return 0;
> }
>
> +static void bq25890_shutdown(struct i2c_client *client)
> +{
> + struct bq25890_device *bq = i2c_get_clientdata(client);
> +
> + /*
> + * TODO this if + return should probably be removed, but that would
> + * introduce a function change for boards using the usb-phy framework.
> + * This needs to be tested on such a board before making this change.
> + */
> + if (!IS_ERR_OR_NULL(bq->usb_phy))
> + return;
> +
> + /*
> + * Turn off the 5v Boost regulator which outputs Vbus to the device's
> + * Micro-USB or Type-C USB port. Leaving this on drains power and
> + * this avoids the PMIC on some device-models seeing this as Vbus
> + * getting inserted after shutdown, causing the device to immediately
> + * power-up again.
> + */
> + bq25890_set_otg_cfg(bq, 0);
> +}
> +
> #ifdef CONFIG_PM_SLEEP
> static int bq25890_suspend(struct device *dev)
> {
> @@ -1161,6 +1240,7 @@ static struct i2c_driver bq25890_driver = {
> },
> .probe = bq25890_probe,
> .remove = bq25890_remove,
> + .shutdown = bq25890_shutdown,
> .id_table = bq25890_i2c_ids,
> };
> module_i2c_driver(bq25890_driver);
> diff --git a/include/linux/power/bq25890_charger.h b/include/linux/power/bq25890_charger.h
> new file mode 100644
> index 000000000000..c706ddb77a08
> --- /dev/null
> +++ b/include/linux/power/bq25890_charger.h
> @@ -0,0 +1,15 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Platform data for the TI bq25890 battery charger driver.
> + */
> +
> +#ifndef _BQ25890_CHARGER_H_
> +#define _BQ25890_CHARGER_H_
> +
> +struct regulator_init_data;
> +
> +struct bq25890_platform_data {
> + const struct regulator_init_data *regulator_init_data;
> +};
> +
> +#endif
> --
> 2.31.1


--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2021-11-16 12:07    [W:0.197 / U:2.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site