lkml.org 
[lkml]   [2021]   [Nov]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 13/20] power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol
Date
From: Yauhen Kharuzhy <jekhor@gmail.com>

Add a "linux,pump-express-vbus-max" property which indicates if the Pump
Express+ protocol should be used to increase the charging protocol.

If this new property is set and a DCP charger is detected then request
a higher charging voltage through the Pump Express+ protocol.

So far this new property is only used on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.

Changes by Hans de Goede:
- Port to my bq25890 patch-series + various cleanups
- Make behavior configurable through a new "linux,pump-express-vbus-max"
device-property
- Sleep 1 second before re-checking the Vbus voltage after requesting
it to be raised, to ensure that the ADC has time to sampled the new Vbus
- Add VBUSV bq25890_tables[] entry and use it in bq25890_get_vbus_voltage()
- Tweak commit message

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/power/supply/bq25890_charger.c | 74 ++++++++++++++++++++++++++
1 file changed, 74 insertions(+)

diff --git a/drivers/power/supply/bq25890_charger.c b/drivers/power/supply/bq25890_charger.c
index 57e4034bc9cd..1c59d4f71389 100644
--- a/drivers/power/supply/bq25890_charger.c
+++ b/drivers/power/supply/bq25890_charger.c
@@ -27,6 +27,10 @@
#define BQ25895_ID 7
#define BQ25896_ID 0

+#define PUMP_EXPRESS_START_DELAY (5 * HZ)
+#define PUMP_EXPRESS_MAX_TRIES 6
+#define PUMP_EXPRESS_VBUS_MARGIN 1000000
+
enum bq25890_chip_version {
BQ25890,
BQ25892,
@@ -107,6 +111,7 @@ struct bq25890_device {
struct usb_phy *usb_phy;
struct notifier_block usb_nb;
struct work_struct usb_work;
+ struct delayed_work pump_express_work;
unsigned long usb_event;

struct regmap *rmap;
@@ -114,6 +119,7 @@ struct bq25890_device {

bool skip_reset;
bool read_back_init_data;
+ u32 pump_express_vbus_max;
enum bq25890_chip_version chip_version;
struct bq25890_init_data init_data;
struct bq25890_state state;
@@ -265,6 +271,7 @@ enum bq25890_table_ids {
TBL_VREG,
TBL_BOOSTV,
TBL_SYSVMIN,
+ TBL_VBUSV,
TBL_VBATCOMP,
TBL_RBATCOMP,

@@ -308,6 +315,7 @@ static const union {
[TBL_VREG] = { .rt = {3840000, 4608000, 16000} }, /* uV */
[TBL_BOOSTV] = { .rt = {4550000, 5510000, 64000} }, /* uV */
[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} }, /* uV */
+ [TBL_VBUSV] = { .rt = {2600000,15300000, 100000} }, /* uV */
[TBL_VBATCOMP] ={ .rt = {0, 224000, 32000} }, /* uV */
[TBL_RBATCOMP] ={ .rt = {0, 140000, 20000} }, /* uOhm */

@@ -410,6 +418,17 @@ static bool bq25890_is_adc_property(enum power_supply_property psp)

static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq);

+static int bq25890_get_vbus_voltage(struct bq25890_device *bq)
+{
+ int ret;
+
+ ret = bq25890_field_read(bq, F_VBUSV);
+ if (ret < 0)
+ return ret;
+
+ return bq25890_find_val(ret, TBL_VBUSV);
+}
+
static int bq25890_power_supply_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
@@ -583,6 +602,11 @@ static void bq25890_charger_external_power_changed(struct power_supply *psy)
switch (val.intval) {
case POWER_SUPPLY_USB_TYPE_DCP:
input_current_limit = bq25890_find_idx(2000000, TBL_IINLIM);
+ if (bq->pump_express_vbus_max) {
+ queue_delayed_work(system_power_efficient_wq,
+ &bq->pump_express_work,
+ PUMP_EXPRESS_START_DELAY);
+ }
break;
case POWER_SUPPLY_USB_TYPE_CDP:
case POWER_SUPPLY_USB_TYPE_ACA:
@@ -847,6 +871,50 @@ static int bq25890_set_otg_cfg(struct bq25890_device *bq, u8 val)
return ret;
}

+static void bq25890_pump_express_work(struct work_struct *data)
+{
+ struct bq25890_device *bq =
+ container_of(data, struct bq25890_device, pump_express_work.work);
+ int voltage, i, ret;
+
+ dev_dbg(bq->dev, "Start to request input voltage increasing\n");
+
+ /* Enable current pulse voltage control protocol */
+ ret = bq25890_field_write(bq, F_PUMPX_EN, 1);
+ if (ret < 0)
+ goto error;
+
+ for (i = 0; i < PUMP_EXPRESS_MAX_TRIES; i++) {
+ voltage = bq25890_get_vbus_voltage(bq);
+ if (voltage < 0)
+ goto error;
+ dev_dbg(bq->dev, "input voltage = %d mV\n", voltage);
+
+ if ((voltage + PUMP_EXPRESS_VBUS_MARGIN) >
+ bq->pump_express_vbus_max)
+ break;
+
+ ret = bq25890_field_write(bq, F_PUMPX_UP, 1);
+ if (ret < 0)
+ goto error;
+
+ while (bq25890_field_read(bq, F_PUMPX_UP) == 1)
+ msleep(100);
+
+ /* Make sure ADC has sampled Vbus before checking again */
+ msleep(1000);
+ }
+
+ bq25890_field_write(bq, F_PUMPX_EN, 0);
+
+ dev_info(bq->dev, "Hi-voltage charging requested, input voltage is %d mV\n",
+ voltage);
+
+ return;
+error:
+ dev_err(bq->dev, "Failed to request hi-voltage charging\n");
+}
+
static void bq25890_usb_work(struct work_struct *data)
{
int ret;
@@ -1037,6 +1105,11 @@ static int bq25890_fw_probe(struct bq25890_device *bq)
int ret;
struct bq25890_init_data *init = &bq->init_data;

+ ret = device_property_read_u32(bq->dev, "linux,pump-express-vbus-max",
+ &bq->pump_express_vbus_max);
+ if (ret < 0)
+ bq->pump_express_vbus_max = 0;
+
bq->skip_reset = device_property_read_bool(bq->dev, "linux,skip-reset");
bq->read_back_init_data = device_property_read_bool(bq->dev,
"linux,read-back-settings");
@@ -1069,6 +1142,7 @@ static int bq25890_probe(struct i2c_client *client,
bq->dev = dev;

mutex_init(&bq->lock);
+ INIT_DELAYED_WORK(&bq->pump_express_work, bq25890_pump_express_work);

bq->rmap = devm_regmap_init_i2c(client, &bq25890_regmap_config);
if (IS_ERR(bq->rmap))
--
2.31.1
\
 
 \ /
  Last update: 2021-11-14 18:06    [W:0.295 / U:3.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site