lkml.org 
[lkml]   [2020]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v4 0/7] mtd: spi-nor: add xSPI Octal DTR support
Date
Hello,

JESD216C has defined specification for Octal 8S-8S-8S and 8D-8D-8D.
Based on JEDEC216C Basic Flash Parameter Table (BFPT) driver extract
DWORD-18: command and command extension type.
DWORD-20: Maximum operation speed of device in Octal mode.

xSPI profile 1.0 table:
DWORD-1: Read Fast command, the number of dummy cycles and address nbytes
for Read Status Register command.
DWORD-2: Read/Write volatile Register command for CFG Reg2.
DWORD-4 and DWORD-5: dummy cycles used for various frequencies based on
maximum speed of device from BFPT 20th DWORD.

Ccommand sequences to change to octal DTR mode:
The length of each command sequence is 8 per byte for single SPI mode and
patching driver to parse and execute these sequences for octal DTR mode.

By Vignesh's comments, this patches set is dependency on Pratyush's
[1][2][5][7][8] and [10][12].

Tested on Macronix's Zynq PicoZed board with Macronix's SPI controller
(spi-mxic.c) driver patched on mx25uw51245g Octal flash.

[1] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-2-p.yadav@ti.com/
[2] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-3-p.yadav@ti.com/
[5] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-6-p.yadav@ti.com/
[7] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-8-p.yadav@ti.com/
[8] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-9-p.yadav@ti.com/
[10] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-11-p.yadav@ti.com/
[12] https://patchwork.ozlabs.org/project/linux-mtd/patch/20200525091544.17270-13-p.yadav@ti.com/

Summary of change log
v4:
Removed Pratyush's patches set part.

v3:
Add support command sequences to change octal DTR mode and based on
part of Pratyush's patches set.

v2:
Parse BFPT & xSPI table for Octal 8D-8D-8D mode parameters and enable Octal
mode in spi_nor_late_init_params().
Using Macros in spi_nor_spimem_read_data, spi_nor_spimem_write_data and
so on by Vignesh comments.

v1:
Without parsing BFPT & xSPI profile 1.0 table and enter Octal 8D-8D-8D
mode directly in spi_nor_fixups hooks.


thnaks for your time and review.
best regards,
Mason

Mason Yang (7):
mtd: spi-nor: sfdp: get octal mode maximum speed from BFPT
mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table
mtd: spi-nor: sfdp: parse command sequences to change octal DTR mode
mtd: spi-nor: core: add configuration register 2 read & write support
mtd: spi-nor: core: execute command sequences to change octal DTR mode
spi: mxic: patch for octal DTR mode support
mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix
mx25uw51245g

drivers/mtd/spi-nor/core.c | 151 ++++++++++++++++++++++++-
drivers/mtd/spi-nor/core.h | 41 +++++++
drivers/mtd/spi-nor/macronix.c | 55 +++++++++
drivers/mtd/spi-nor/sfdp.c | 246 +++++++++++++++++++++++++++++++++++++++++
drivers/mtd/spi-nor/sfdp.h | 4 +
drivers/spi/spi-mxic.c | 98 ++++++++++------
6 files changed, 562 insertions(+), 33 deletions(-)

--
1.9.1

\
 
 \ /
  Last update: 2020-05-29 09:37    [W:0.212 / U:1.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site