lkml.org 
[lkml]   [2020]   [Oct]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v4 4/7] mtd: spi-nor: core: add configuration register 2 read & write support
Date
Hi, Mason, YC Lin,

On 5/29/20 10:36 AM, Mason Yang wrote:
> Configuration register 2 is to set the device operation condition like
> STR or DTR mode at address offset 0 and DQS mode at address offset 0x200.
>
> Each device has various address offset for it's specific operatoin
> setting.
>
> Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
> ---
> drivers/mtd/spi-nor/core.c | 78 ++++++++++++++++++++++++++++++++++++++++++++++
> drivers/mtd/spi-nor/core.h | 2 ++
> 2 files changed, 80 insertions(+)
>
> diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
> index 3799417..fed6236 100644
> --- a/drivers/mtd/spi-nor/core.c
> +++ b/drivers/mtd/spi-nor/core.c
> @@ -269,6 +269,84 @@ int spi_nor_write_disable(struct spi_nor *nor)
> }
>
> /**
> + * spi_nor_read_cr2() - Read the Configuration Register 2.
> + * @nor: pointer to 'struct spi_nor'.
> + * @addr: offset address to read.
> + * @cr2: pointer to a DMA-able buffer where the value of the
> + * Configuration Register 2 will be written.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +int spi_nor_read_cr2(struct spi_nor *nor, u32 addr, u8 *cr2)

spi_nor_read_volatile_reg() please

do we need to pass len as an argument?

s/cr2/buf

why do we need addr for register interactions?

> +{
> + int ret;
> + u8 cmd = nor->params->rd_reg_cmd;

you'll need to redefine to rd_vreg_cmd.

> +
> + if (nor->spimem) {
> + struct spi_mem_op op =
> + SPI_MEM_OP(SPI_MEM_OP_CMD(cmd, 1),
> + SPI_MEM_OP_ADDR(4, addr, 1),

nor->addr_width?

> + SPI_MEM_OP_DUMMY(4, 1),

nor->read_dummy?

> + SPI_MEM_OP_DATA_IN(1, cr2, 1));

SPI_MEM_OP_DATA_IN(len, cr2, 0)?
> +
> + spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
> +
> + ret = spi_mem_exec_op(nor->spimem, &op);
> + } else {
> + if (spi_nor_protocol_is_dtr(nor->reg_proto))
> + ret = -ENOTSUPP;
> + else
> + ret = nor->controller_ops->read_reg(nor, cmd, cr2, 1);
> + }
> +
> + if (ret)
> + dev_dbg(nor->dev, "error %d reading CR2\n", ret);
> +
> + return ret;
> +}
> +
> +/**
> + * spi_nor_write_cr2() - Write the Configuration Register 2.
> + * @nor: pointer to 'struct spi_nor'.
> + * @addr: offset address to write.
> + * @cr2: pointer to a DMA-able buffer where the value of the
> + * Configuratin Register 2 will be read.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +int spi_nor_write_cr2(struct spi_nor *nor, u32 addr, u8 *cr2)

spi_nor_write_volatile_reg() please

Cheers,
ta
\
 
 \ /
  Last update: 2020-10-28 23:23    [W:0.535 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site