lkml.org 
[lkml]   [2014]   [Feb]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] i2c: Add message transfer tracepoints for I2C
Hi David,

On Thu, Jan 09, 2014 at 09:49:54PM +0000, David Howells wrote:
> Add tracepoints into the I2C message transfer function to retrieve the message
> sent or received. The following config options must be turned on to make use
> of the facility:
>
> CONFIG_FTRACE
> CONFIG_ENABLE_DEFAULT_TRACERS
>
> The I2C tracepoint can be enabled thusly:
>
> echo 1 >/sys/kernel/debug/tracing/events/i2c/i2c_transfer/enable
>
> and will dump messages that can be viewed in /sys/kernel/debug/tracing/trace
> that look like:
>
> ... i2c_write: i2c-5 #0 f=00 a=44 l=2 [0214]
> ... i2c_read: i2c-5 #1 f=01 a=44 l=4
> ... i2c_reply: i2c-5 #1 f=01 a=44 l=4 [33000000]
> ... i2c_result: i2c-5 n=2 ret=2
>
> formatted as:
>
> i2c-<adapter-nr>
> #<message-array-index>
> f=<flags>
> a=<addr>
> l=<datalen>
> n=<message-array-size>
> ret=<result>
> [<data>]
>
> The operation is done between the i2c_write/i2c_read lines and the i2c_reply
> and i2c_result lines so that if the hardware hangs, the trace buffer can be
> consulted to determine the problematic operation.
>
> The adapters to be traced can be selected by something like:
>
> echo adapter_nr==1 >/sys/kernel/debug/tracing/events/i2c/filter
>
> These changes are based on code from Steven Rostedt.
>
> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
> Signed-off-by: David Howells <dhowells@redhat.com>
> Reviewed-by: Steven Rostedt <rostedt@goodmis.org>

I like it very much, just have some comments about the format.

> +TRACE_EVENT_FN(i2c_write,
> + TP_PROTO(const struct i2c_adapter *adap, const struct i2c_msg *msg,
> + int num),
> + TP_ARGS(adap, msg, num),
> + TP_STRUCT__entry(
> + __field(int, adapter_nr )
> + __field(__u16, msg_nr )
> + __field(__u16, addr )
> + __field(__u16, flags )
> + __field(__u16, len )
> + __dynamic_array(__u8, buf, msg->len) ),
> + TP_fast_assign(
> + __entry->adapter_nr = adap->nr;
> + __entry->msg_nr = num;
> + __entry->addr = msg->addr;
> + __entry->flags = msg->flags;
> + __entry->len = msg->len;
> + memcpy(__get_dynamic_array(buf), msg->buf, msg->len);
> + ),
> + TP_printk("i2c-%d #%u f=%02x a=%02x l=%u [%*phN]",

'flags' are u16 and the whole range is needed -> %04x

'addr' is u16 and either 7 or 10 bits are needed. The core does the
following when assigning names because it is possible to have devices
0x50 (7-bit) and 0x050 (10-bit) on the bus:

/* For 10-bit clients, add an arbitrary offset to avoid collisions */
dev_set_name(&client->dev, "%d-%04x", i2c_adapter_id(adap),
client->addr | ((client->flags & I2C_CLIENT_TEN)
? 0xa000 : 0));

I don't know if this can be implemented. Actually, I don't think it
needs to be implemented since flags are printed, too. So, with this the
10-bit case is visible and for the address simply %03x should do.

And for the buffer: %*phN is difficult to read IMO. What about %*ph? Or
%*phD at least?

Thanks,

Wolfram

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2014-02-18 22:41    [W:0.129 / U:0.576 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site