lkml.org 
[lkml]   [2023]   [Feb]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] net: phy: at803x: fix the wol setting functions
Date
In 7beecaf7d507 ("net: phy: at803x: improve the WOL feature"), it seems
not correct to use a wol_en bit in a 1588 Control Register which is only
available on AR8031/AR8033(share the same phy_id) to determine if WoL is
enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also
update the at803x_set_wol() function to only update the 1588 register on
chips having it. After this change, disabling wol at probe from
d7cd5e06c9dd ("net: phy: at803x: disable WOL at probe") is no longer
needed. So it is removed.

Also remove the set_wol()/get_wol() callbacks from AR8032 which doesn't
support WoL.

Fixes: 7beecaf7d507b ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
---
drivers/net/phy/at803x.c | 42 +++++++++++++++-------------------------
1 file changed, 16 insertions(+), 26 deletions(-)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 22f4458274aa..ac47a1d681b2 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -461,21 +461,25 @@ static int at803x_set_wol(struct phy_device *phydev,
phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
mac[(i * 2) + 1] | (mac[(i * 2)] << 8));

- /* Enable WOL function */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
- 0, AT803X_WOL_EN);
- if (ret)
- return ret;
+ /* Enable WOL function for 1588 */
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
+ 0, AT803X_WOL_EN);
+ if (ret)
+ return ret;
+ }
/* Enable WOL interrupt */
ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
if (ret)
return ret;
} else {
- /* Disable WoL function */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
- AT803X_WOL_EN, 0);
- if (ret)
- return ret;
+ /* Disable WoL function for 1588 */
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
+ AT803X_WOL_EN, 0);
+ if (ret)
+ return ret;
+ }
/* Disable WOL interrupt */
ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
if (ret)
@@ -510,11 +514,8 @@ static void at803x_get_wol(struct phy_device *phydev,
wol->supported = WAKE_MAGIC;
wol->wolopts = 0;

- value = phy_read_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL);
- if (value < 0)
- return;
-
- if (value & AT803X_WOL_EN)
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (value & AT803X_INTR_ENABLE_WOL)
wol->wolopts |= WAKE_MAGIC;
}

@@ -866,9 +867,6 @@ static int at803x_probe(struct phy_device *phydev)
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
int mode_cfg;
- struct ethtool_wolinfo wol = {
- .wolopts = 0,
- };

if (ccr < 0) {
ret = ccr;
@@ -887,12 +885,6 @@ static int at803x_probe(struct phy_device *phydev)
break;
}

- /* Disable WOL by default */
- ret = at803x_set_wol(phydev, &wol);
- if (ret < 0) {
- phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
- goto err;
- }
}

return 0;
@@ -2087,8 +2079,6 @@ static struct phy_driver at803x_driver[] = {
.flags = PHY_POLL_CABLE_TEST,
.config_init = at803x_config_init,
.link_change_notify = at803x_link_change_notify,
- .set_wol = at803x_set_wol,
- .get_wol = at803x_get_wol,
.suspend = at803x_suspend,
.resume = at803x_resume,
/* PHY_BASIC_FEATURES */
--
2.38.0
\
 
 \ /
  Last update: 2023-03-27 00:31    [W:0.027 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site