lkml.org 
[lkml]   [2022]   [Aug]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 2/2] spi: microchip-core-qspi: Add support for microchip fpga qspi controllers
Hi Conor,

On Mon, Aug 1, 2022 at 4:19 PM <Conor.Dooley@microchip.com> wrote:
>
> On 01/08/2022 10:42, Naga Sureshkumar Relli wrote:
> > Add a driver for Microchip FPGA QSPI controllers. This driver also
> > supports "hard" QSPI controllers on Polarfire SoC.
> >
> > Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
> > ---
>
> ---8<---
>
> > +static int mchp_coreqspi_probe(struct platform_device *pdev)
> > +{
> > + struct spi_controller *ctlr;
> > + struct mchp_coreqspi *qspi;
> > + struct device *dev = &pdev->dev;
> > + struct device_node *np = dev->of_node;
> > + int ret;
> > +
> > + ctlr = spi_alloc_master(&pdev->dev, sizeof(*qspi));
> > + if (!ctlr)
> > + return -ENOMEM;
>
> Argh... I am sorry for not mentioning this when you asked me if
> I thought the driver was ready to be sent upstream, but I think
> we should try to use the devm_ versions of these functions.
Ok.
>
> > +
> > + qspi = spi_controller_get_devdata(ctlr);
>
> Is there a reason to use spi_controller_get_devdata() rather than
> spi_master_get_devdata() ?
Both are the same.
https://github.com/torvalds/linux/blob/master/include/linux/spi/spi.h#L1497
Ref: https://github.com/torvalds/linux/commit/8caab75fd2c2a92667cbb1cd315720bede3feaa9
>
> > + platform_set_drvdata(pdev, qspi);
> > +
> > + qspi->regs = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(qspi->regs)) {
> > + ret = PTR_ERR(qspi->regs);
> > + goto remove_master;
>
> Using devm_spi_alloc_master() above would simplify this
> to just a return of dev_err_probe() & ditto for every
> time we do a "goto remove_master"
Ok. I will update to use devm_ versions.
>
> > + }
> > +
> > + qspi->clk = devm_clk_get(&pdev->dev, NULL);
> > + if (IS_ERR(qspi->clk)) {
> > + dev_err(&pdev->dev, "clock not found.\n");
> > + ret = PTR_ERR(qspi->clk);
> > + goto remove_master;
> > + }
> > +
> > + ret = clk_prepare_enable(qspi->clk);
> > + if (ret) {
> > + dev_err(&pdev->dev, "failed to enable clock\n");
> > + goto remove_master;
> > + }
> > +
> > + init_completion(&qspi->data_completion);
> > + mutex_init(&qspi->op_lock);
> > +
> > + qspi->irq = platform_get_irq(pdev, 0);
> > + if (qspi->irq <= 0) {
> > + ret = qspi->irq;
> > + goto clk_dis_all;
> > + }
> > +
> > + ret = devm_request_irq(&pdev->dev, qspi->irq, mchp_coreqspi_isr,
> > + 0, pdev->name, qspi);
> > + if (ret != 0) {
> > + dev_err(&pdev->dev, "request_irq failed %d\n", ret);
> > + goto clk_dis_all;
> > + }
> > +
> > + ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
> > + ctlr->mem_ops = &mchp_coreqspi_mem_ops;
> > + ctlr->setup = mchp_coreqspi_setup_op;
> > + ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
> > + SPI_TX_DUAL | SPI_TX_QUAD;
> > + ctlr->dev.of_node = np;
> > +
> > + ret = devm_spi_register_controller(&pdev->dev, ctlr);
> > + if (ret) {
> > + dev_err(&pdev->dev, "spi_register_controller failed\n");
> > + goto clk_dis_all;
> > + }
> > +
> > + return 0;
> > +
> > +clk_dis_all:
> > + clk_disable_unprepare(qspi->clk);
>
> If we move the clk prepare & enable later in probe, ie after
> getting the irq, this goto could be removed too because the
> only place requiring teardown of the clock would be the error
> path of devm_spi_register_controller().
ok.
>
> > +remove_master:
> > + spi_controller_put(ctlr);
>
> With devm_spi_alloc_master() this put is no longer needed &
> we can return a nice dev_err_probe() for each error :)
ok. I will send the next version with these updates.
>
> > +
> > + return ret;
> > +}
>
> Thanks Suresh.
> Conor.

\
 
 \ /
  Last update: 2022-08-01 13:10    [W:0.107 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site