lkml.org 
[lkml]   [2022]   [May]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RESEND PATCH v5] PCI: Make sure the bus bridge powered on when scanning bus
On Tue, May 24, 2022 at 10:58 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
>
> On Tue, May 17, 2022 at 08:43:19PM +0800, Yicong Yang wrote:
> > When the bus bridge is runtime suspended, we'll fail to rescan
> > the devices through sysfs as we cannot access the configuration
> > space correctly when the bridge is in D3hot.
>
> Is the "D3hot" above a typo? I think devices are supposed to respond
> to config accesses when in D3hot. PCIe r6.0, sec 5.3.1.4.1:
>
> Configuration and Message requests are the only TLPs accepted by a
> Function in the D3Hot state. ...
>
> Functions that are in D3Hot are permitted to be transitioned by
> software (writing to their PMCSR PowerState field) to the D0active
> state or the D0uninitialized state. Functions that are in D3Hot must
> respond to Configuration Space accesses as long as power and clock
> are supplied so that they can be returned to D0 by software.

That applies to the device itself, though, and not to the bus under it.

In general, a bridge in D3hot causes the bus segment on the other side
of it to be inaccessible even for config space accesses AFAICS.

> > It can be reproduced like:
> >
> > $ echo 1 > /sys/bus/pci/devices/0000:80:00.0/0000:81:00.1/remove
> > $ echo 1 > /sys/bus/pci/devices/0000:80:00.0/pci_bus/0000:81/rescan
> >
> > 0000:80:00.0 is a Root Port and it is runtime-suspended, so
> > 0000:81:00.1 is unreachable after a rescan.
> >
> > Power up the bridge when scanning the child bus and allow it to
> > suspend again by adding pm_runtime_get_sync()/pm_runtime_put()
> > in pci_scan_child_bus_extend().
> >
> > Cc: Rafael J. Wysocki <rafael@kernel.org>
> > Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
> > Cc: Bjorn Helgaas <bhelgaas@google.com>
> > Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
> > Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> > ---
> > drivers/pci/probe.c | 12 ++++++++++++
> > 1 file changed, 12 insertions(+)
> >
> > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> > index 17a969942d37..b108e72b6586 100644
> > --- a/drivers/pci/probe.c
> > +++ b/drivers/pci/probe.c
> > @@ -2859,11 +2859,20 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
> > unsigned int used_buses, normal_bridges = 0, hotplug_bridges = 0;
> > unsigned int start = bus->busn_res.start;
> > unsigned int devfn, fn, cmax, max = start;
> > + struct pci_dev *bridge = bus->self;
> > struct pci_dev *dev;
> > int nr_devs;
> >
> > dev_dbg(&bus->dev, "scanning bus\n");
> >
> > + /*
> > + * Make sure the bus bridge is powered on, otherwise we may not be
> > + * able to scan the devices as we may fail to access the configuration
> > + * space of subordinates.
> > + */
> > + if (bridge)
> > + pm_runtime_get_sync(&bridge->dev);
> > +
> > /* Go find them, Rover! */
> > for (devfn = 0; devfn < 256; devfn += 8) {
> > nr_devs = pci_scan_slot(bus, devfn);
> > @@ -2976,6 +2985,9 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
> > }
> > }
> >
> > + if (bridge)
> > + pm_runtime_put(&bridge->dev);
> > +
> > /*
> > * We've scanned the bus and so we know all about what's on
> > * the other side of any bridges that may be on this bus plus
> > --
> > 2.24.0
> >

\
 
 \ /
  Last update: 2022-05-25 13:28    [W:0.105 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site