lkml.org 
[lkml]   [2022]   [May]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RESEND PATCH v5] PCI: Make sure the bus bridge powered on when scanning bus
On Tue, May 17, 2022 at 08:43:19PM +0800, Yicong Yang wrote:
> When the bus bridge is runtime suspended, we'll fail to rescan
> the devices through sysfs as we cannot access the configuration
> space correctly when the bridge is in D3hot.

Is the "D3hot" above a typo? I think devices are supposed to respond
to config accesses when in D3hot. PCIe r6.0, sec 5.3.1.4.1:

Configuration and Message requests are the only TLPs accepted by a
Function in the D3Hot state. ...

Functions that are in D3Hot are permitted to be transitioned by
software (writing to their PMCSR PowerState field) to the D0active
state or the D0uninitialized state. Functions that are in D3Hot must
respond to Configuration Space accesses as long as power and clock
are supplied so that they can be returned to D0 by software.

> It can be reproduced like:
>
> $ echo 1 > /sys/bus/pci/devices/0000:80:00.0/0000:81:00.1/remove
> $ echo 1 > /sys/bus/pci/devices/0000:80:00.0/pci_bus/0000:81/rescan
>
> 0000:80:00.0 is a Root Port and it is runtime-suspended, so
> 0000:81:00.1 is unreachable after a rescan.
>
> Power up the bridge when scanning the child bus and allow it to
> suspend again by adding pm_runtime_get_sync()/pm_runtime_put()
> in pci_scan_child_bus_extend().
>
> Cc: Rafael J. Wysocki <rafael@kernel.org>
> Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
> Cc: Bjorn Helgaas <bhelgaas@google.com>
> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> ---
> drivers/pci/probe.c | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> index 17a969942d37..b108e72b6586 100644
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -2859,11 +2859,20 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
> unsigned int used_buses, normal_bridges = 0, hotplug_bridges = 0;
> unsigned int start = bus->busn_res.start;
> unsigned int devfn, fn, cmax, max = start;
> + struct pci_dev *bridge = bus->self;
> struct pci_dev *dev;
> int nr_devs;
>
> dev_dbg(&bus->dev, "scanning bus\n");
>
> + /*
> + * Make sure the bus bridge is powered on, otherwise we may not be
> + * able to scan the devices as we may fail to access the configuration
> + * space of subordinates.
> + */
> + if (bridge)
> + pm_runtime_get_sync(&bridge->dev);
> +
> /* Go find them, Rover! */
> for (devfn = 0; devfn < 256; devfn += 8) {
> nr_devs = pci_scan_slot(bus, devfn);
> @@ -2976,6 +2985,9 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
> }
> }
>
> + if (bridge)
> + pm_runtime_put(&bridge->dev);
> +
> /*
> * We've scanned the bus and so we know all about what's on
> * the other side of any bridges that may be on this bus plus
> --
> 2.24.0
>

\
 
 \ /
  Last update: 2022-05-24 22:59    [W:0.115 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site