lkml.org 
[lkml]   [2022]   [Dec]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 09/23] phy: qcom-qmp-ufs: Avoid setting HS G3 specific registers
Date
SM8350 default init sequence sets some PCS registers to HS G3, thereby
disabling HS G4 mode. This has the effect on MPHY capability negotiation
between the host and the device during link startup and causes the
PA_MAXHSGEAR to G3 irrespective of device max gear.

Due to that, the agreed gear speed determined by the UFS core will become
G3 only and the platform won't run at G4.

So, let's remove setting these registers for SM8350 as like other G4
compatible platforms. One downside of this is that, when the board design
uses non-G4 compatible device, then MPHY will continue to run in the
default mode (G4) even if UFSHCD runs in G3. But this is the case for
other platforms as well.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 7 -------
1 file changed, 7 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
index d5324c4e8513..6c7c6a06fe3b 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
@@ -567,13 +567,6 @@ static const struct qmp_phy_init_tbl sm8350_ufsphy_pcs[] = {
QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1f),
QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_PLL_CNTL, 0x03),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xd8),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_PWM_GEAR_BAND, 0xaa),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HS_GEAR_BAND, 0x06),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03),
- QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03),
QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_SIGDET_CTRL1, 0x0e),
QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
};
--
2.25.1
\
 
 \ /
  Last update: 2022-12-01 18:46    [W:0.638 / U:1.396 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site