Messages in this thread | | | Date | Wed, 16 Nov 2022 12:06:19 +0100 | Subject | Re: [PATCH 03/10] arm64: dts: qcom: Add pm8010 pmic dtsi | From | Konrad Dybcio <> |
| |
On 16/11/2022 11:31, Abel Vesa wrote: > From: Neil Armstrong <neil.armstrong@linaro.org> > > Add nodes for pm8010 in separate dtsi file. > > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad > arch/arm64/boot/dts/qcom/pm8010.dtsi | 84 ++++++++++++++++++++++++++++ > 1 file changed, 84 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pm8010.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pm8010.dtsi b/arch/arm64/boot/dts/qcom/pm8010.dtsi > new file mode 100644 > index 000000000000..0ea641e12209 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pm8010.dtsi > @@ -0,0 +1,84 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2022, Linaro Limited > + */ > + > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pm8010-m-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pm8010_m_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + }; > + }; > + > + pm8010-n-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pm8010_n_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + }; > + }; > + }; > +}; > + > + > +&spmi_bus { > + pm8010_m: pmic@c { > + compatible = "qcom,pm8010", "qcom,spmi-pmic"; > + reg = <0xc SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pm8010_m_temp_alarm: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + }; > + > + pm8010_n: pmic@d { > + compatible = "qcom,pm8010", "qcom,spmi-pmic"; > + reg = <0xd SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pm8010_n_temp_alarm: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0xd 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + }; > +};
| |