lkml.org 
[lkml]   [2021]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 08/11] drm/msm/disp/dpu1: Add support for DSC in encoder
From
Date
On 15/07/2021 09:52, Vinod Koul wrote:
> When DSC is enabled in DT, we need to configure the encoder for DSC
> configuration, calculate DSC parameters for the given timing.
>
> This patch adds that support by adding dpu_encoder_prep_dsc() which is
> invoked when DSC is enabled in DT
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 142 +++++++++++++++++++-
> 1 file changed, 141 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> index 8d942052db8a..41140b781e66 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> @@ -21,12 +21,17 @@
> #include "dpu_hw_intf.h"
> #include "dpu_hw_ctl.h"
> #include "dpu_hw_dspp.h"
> +#include "dpu_hw_dsc.h"
> #include "dpu_formats.h"
> #include "dpu_encoder_phys.h"
> #include "dpu_crtc.h"
> #include "dpu_trace.h"
> #include "dpu_core_irq.h"
>
> +#define DSC_MODE_SPLIT_PANEL BIT(0)
> +#define DSC_MODE_MULTIPLEX BIT(1)
> +#define DSC_MODE_VIDEO BIT(2)

This should go into dpu_hw_dsc.h. Ah. They are already defined there and
just redefined there. Remove the defines here.

It might be cleaner to add bool flags to struct msm_display_dsc_config
and then calculate common mode in the dpu_hw_dsc_config().


> +
> #define DPU_DEBUG_ENC(e, fmt, ...) DPU_DEBUG("enc%d " fmt,\
> (e) ? (e)->base.base.id : -1, ##__VA_ARGS__)
>
> @@ -135,6 +140,7 @@ enum dpu_enc_rc_states {
> * @cur_slave: As above but for the slave encoder.
> * @hw_pp: Handle to the pingpong blocks used for the display. No.
> * pingpong blocks can be different than num_phys_encs.
> + * @hw_dsc Handle to the DSC blocks used for the display.
> * @intfs_swapped: Whether or not the phys_enc interfaces have been swapped
> * for partial update right-only cases, such as pingpong
> * split where virtual pingpong does not generate IRQs
> @@ -180,6 +186,7 @@ struct dpu_encoder_virt {
> struct dpu_encoder_phys *cur_master;
> struct dpu_encoder_phys *cur_slave;
> struct dpu_hw_pingpong *hw_pp[MAX_CHANNELS_PER_ENC];
> + struct dpu_hw_dsc *hw_dsc[MAX_CHANNELS_PER_ENC];
>
> bool intfs_swapped;
>
> @@ -1008,7 +1015,8 @@ static void dpu_encoder_virt_mode_set(struct drm_encoder *drm_enc,
> struct dpu_hw_blk *hw_ctl[MAX_CHANNELS_PER_ENC];
> struct dpu_hw_blk *hw_lm[MAX_CHANNELS_PER_ENC];
> struct dpu_hw_blk *hw_dspp[MAX_CHANNELS_PER_ENC] = { NULL };
> - int num_lm, num_ctl, num_pp;
> + struct dpu_hw_blk *hw_dsc[MAX_CHANNELS_PER_ENC];
> + int num_lm, num_ctl, num_pp, num_dsc;
> int i, j;
>
> if (!drm_enc) {
> @@ -1061,11 +1069,16 @@ static void dpu_encoder_virt_mode_set(struct drm_encoder *drm_enc,
> dpu_rm_get_assigned_resources(&dpu_kms->rm, global_state,
> drm_enc->base.id, DPU_HW_BLK_DSPP, hw_dspp,
> ARRAY_SIZE(hw_dspp));
> + num_dsc = dpu_rm_get_assigned_resources(&dpu_kms->rm, global_state,
> + drm_enc->base.id, DPU_HW_BLK_DSC, hw_dsc, ARRAY_SIZE(hw_dsc));
>
> for (i = 0; i < MAX_CHANNELS_PER_ENC; i++)
> dpu_enc->hw_pp[i] = i < num_pp ? to_dpu_hw_pingpong(hw_pp[i])
> : NULL;
>
> + for (i = 0; i < MAX_CHANNELS_PER_ENC; i++)
> + dpu_enc->hw_dsc[i] = i < num_dsc ? to_dpu_hw_dsc(hw_dsc[i]) : NULL;
> +
> cstate = to_dpu_crtc_state(drm_crtc->state);
>
> for (i = 0; i < num_lm; i++) {
> @@ -1810,10 +1823,133 @@ static void dpu_encoder_vsync_event_work_handler(struct kthread_work *work)
> nsecs_to_jiffies(ktime_to_ns(wakeup_time)));
> }
>
> +static void
> +dpu_encoder_dsc_pclk_param_calc(struct msm_display_dsc_config *dsc, u32 width)
> +{
> + int slice_count, slice_per_intf;
> + int bytes_in_slice, total_bytes_per_intf;
> +
> + if (!dsc || !dsc->drm->slice_width || !dsc->drm->slice_count) {
> + DPU_ERROR("Invalid DSC/slices\n");
> + return;
> + }
> +
> + slice_count = dsc->drm->slice_count;
> + slice_per_intf = DIV_ROUND_UP(width, dsc->drm->slice_width);
> +
> + /*
> + * If slice_count is greater than slice_per_intf then default to 1.
> + * This can happen during partial update.
> + */
> + if (slice_count > slice_per_intf)
> + slice_count = 1;
> +
> + bytes_in_slice = DIV_ROUND_UP(dsc->drm->slice_width *
> + dsc->drm->bits_per_pixel, 8);
> + total_bytes_per_intf = bytes_in_slice * slice_per_intf;
> +
> + dsc->eol_byte_num = total_bytes_per_intf % 3;
> + dsc->pclk_per_line = DIV_ROUND_UP(total_bytes_per_intf, 3);
> + dsc->bytes_in_slice = bytes_in_slice;
> + dsc->bytes_per_pkt = bytes_in_slice * slice_count;
> + dsc->pkt_per_line = slice_per_intf / slice_count;
> +}
> +
> +static void
> +dpu_encoder_dsc_initial_line_calc(struct msm_display_dsc_config *dsc,
> + u32 enc_ip_width)
> +{
> + int ssm_delay, total_pixels, soft_slice_per_enc;
> +
> + soft_slice_per_enc = enc_ip_width / dsc->drm->slice_width;
> +
> + /*
> + * minimum number of initial line pixels is a sum of:
> + * 1. sub-stream multiplexer delay (83 groups for 8bpc,
> + * 91 for 10 bpc) * 3
> + * 2. for two soft slice cases, add extra sub-stream multiplexer * 3
> + * 3. the initial xmit delay
> + * 4. total pipeline delay through the "lock step" of encoder (47)
> + * 5. 6 additional pixels as the output of the rate buffer is
> + * 48 bits wide
> + */
> + ssm_delay = ((dsc->drm->bits_per_component < 10) ? 84 : 92);
> + total_pixels = ssm_delay * 3 + dsc->drm->initial_xmit_delay + 47;
> + if (soft_slice_per_enc > 1)
> + total_pixels += (ssm_delay * 3);
> + dsc->initial_lines = DIV_ROUND_UP(total_pixels, dsc->drm->slice_width);
> +}
> +
> +static void dpu_encoder_dsc_pipe_cfg(struct dpu_hw_dsc *hw_dsc,
> + struct dpu_hw_pingpong *hw_pp,
> + struct msm_display_dsc_config *dsc,
> + u32 common_mode)
> +{
> + if (hw_dsc->ops.dsc_config)
> + hw_dsc->ops.dsc_config(hw_dsc, dsc, common_mode);
> +
> + if (hw_dsc->ops.dsc_config_thresh)
> + hw_dsc->ops.dsc_config_thresh(hw_dsc, dsc);
> +
> + if (hw_pp->ops.setup_dsc)
> + hw_pp->ops.setup_dsc(hw_pp);
> +
> + if (hw_pp->ops.enable_dsc)
> + hw_pp->ops.enable_dsc(hw_pp);

I think, we do not need to split these operations, I'd suggest having
just hw_dsc->ops.dsc_config() and hw_pp->ops.enable_dsc(), merging
dsc_config_thres() and setup_dsc() into respective methods.

> +}
> +
> +static void dpu_encoder_prep_dsc(struct dpu_encoder_virt *dpu_enc,
> + struct msm_display_dsc_config *dsc)
> +{
> + /* coding only for 2LM, 2enc, 1 dsc config */
> + struct dpu_encoder_phys *enc_master = dpu_enc->cur_master;
> + struct dpu_hw_dsc *hw_dsc[MAX_CHANNELS_PER_ENC];
> + struct dpu_hw_pingpong *hw_pp[MAX_CHANNELS_PER_ENC];
> + int this_frame_slices;
> + int intf_ip_w, enc_ip_w;
> + int dsc_common_mode;
> + int pic_width, pic_height;
> + int i;
> +
> + for (i = 0; i < MAX_CHANNELS_PER_ENC; i++) {
> + hw_pp[i] = dpu_enc->hw_pp[i];
> + hw_dsc[i] = dpu_enc->hw_dsc[i];
> +
> + if (!hw_pp[i] || !hw_dsc[i]) {
> + DPU_ERROR_ENC(dpu_enc, "invalid params for DSC\n");
> + return;
> + }
> + }
> +
> + dsc_common_mode = 0;
> + pic_width = dsc->drm->pic_width;
> + pic_height = dsc->drm->pic_height;
> +
> + dsc_common_mode = DSC_MODE_MULTIPLEX | DSC_MODE_SPLIT_PANEL;
> + if (enc_master->intf_mode == INTF_MODE_VIDEO)
> + dsc_common_mode |= DSC_MODE_VIDEO;
> +
> + this_frame_slices = pic_width / dsc->drm->slice_width;
> + intf_ip_w = this_frame_slices * dsc->drm->slice_width;
> +
> + dpu_encoder_dsc_pclk_param_calc(dsc, intf_ip_w);
> +
> + /*
> + * dsc merge case: when using 2 encoders for the same stream,
> + * no. of slices need to be same on both the encoders.
> + */
> + enc_ip_w = intf_ip_w / 2;
> + dpu_encoder_dsc_initial_line_calc(dsc, enc_ip_w);
> +
> + for (i = 0; i < MAX_CHANNELS_PER_ENC; i++)
> + dpu_encoder_dsc_pipe_cfg(hw_dsc[i], hw_pp[i], dsc, dsc_common_mode);
> +}
> +
> void dpu_encoder_prepare_for_kickoff(struct drm_encoder *drm_enc)
> {
> struct dpu_encoder_virt *dpu_enc;
> struct dpu_encoder_phys *phys;
> + struct msm_drm_private *priv;
> bool needs_hw_reset = false;
> unsigned int i;
>
> @@ -1841,6 +1977,10 @@ void dpu_encoder_prepare_for_kickoff(struct drm_encoder *drm_enc)
> dpu_encoder_helper_hw_reset(dpu_enc->phys_encs[i]);
> }
> }
> +
> + priv = drm_enc->dev->dev_private;
> + if (priv->dsc)
> + dpu_encoder_prep_dsc(dpu_enc, priv->dsc);

Not quite. This makes dsc config global, while we can have several
encoders enabled at once (think of DSI + DP). So the dsc should be a
per-encoder setting rather than global.

> }
>
> void dpu_encoder_kickoff(struct drm_encoder *drm_enc)
>


--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2021-07-29 22:55    [W:0.514 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site