lkml.org 
[lkml]   [2021]   [Oct]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 09/22] PCI: aardvark: Use SET_PCI_ERROR_RESPONSE() when device not found
On 11/10, Pali Rohár wrote:
> On Monday 11 October 2021 23:55:35 Naveen Naidu wrote:
> > On 11/10, Pali Rohár wrote:
> > > On Monday 11 October 2021 23:26:33 Naveen Naidu wrote:
> > > > An MMIO read from a PCI device that doesn't exist or doesn't respond
> > > > causes a PCI error. There's no real data to return to satisfy the
> > > > CPU read, so most hardware fabricates ~0 data.
> > > >
> > > > Use SET_PCI_ERROR_RESPONSE() to set the error response, when a faulty
> > > > read occurs.
> > > >
> > > > This helps unify PCI error response checking and make error check
> > > > consistent and easier to find.
> > > >
> > > > Compile tested only.
> > > >
> > > > Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
> > > > ---
> > > > drivers/pci/controller/pci-aardvark.c | 8 ++++----
> > > > 1 file changed, 4 insertions(+), 4 deletions(-)
> > > >
> > > > diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
> > > > index 596ebcfcc82d..dc2f820ef55f 100644
> > > > --- a/drivers/pci/controller/pci-aardvark.c
> > > > +++ b/drivers/pci/controller/pci-aardvark.c
> > > > @@ -894,7 +894,7 @@ static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn,
> > > > int ret;
> > > >
> > > > if (!advk_pcie_valid_device(pcie, bus, devfn)) {
> > > > - *val = 0xffffffff;
> > > > + SET_PCI_ERROR_RESPONSE(val);
> > >
> > > Hello! Now I'm looking at this macro, and should not it depends on
> > > "size" argument? If doing 8-bit or 16-bit read operation then should not
> > > it rather sets only low 8 bits or low 16 bits to ones?
> > >
> >
> > Hello o/, Thank you for the review.
> >
> > Yes! you are right that it should indeed depend on the "size" argument.
> > And that is what the SET_PCI_ERROR_RESPONSE macro does. The macro is
> > defined as:
> >
> > #define PCI_ERROR_RESPONSE (~0ULL)
> > #define SET_PCI_ERROR_RESPONSE(val) (*val = ((typeof(*val))PCI_ERROR_RESPONSE))
> >
> > The macro was part of "Patch 1/22" and is present here [1]. Apologies if
> > I added the receipient incorrectly.
> >
> > [1]:
> > https://lore.kernel.org/linux-pci/d8e423386aad3d78bca575a7521b138508638e3b.1633972263.git.naveennaidu479@gmail.com/T/#m37295a0dcfe0d7e0f67efce3633efd7b891949c4
> >
> > IIUC, the typeof(*val) helps in setting the value according to the size
> > of the argument.
> >
> > Please let me know if my understanding is wrong.
>
> Hello! I mean "size" function argument which is passed as variable.
>

Thank you for explaining! Now I understand what you mean :), Apologies
for not being not understanding this beforehand.

> Function itself is declared as:
>
> static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 *val);
>
> And in "size" argument is stored number of bytes, kind of read operation
> (read byte, read word, read dword). In *val is then stored read value.
> For byte operation, just low 8 bits in *val variable are set.
>
> Because *val is u32 it means that typeof(*val) is always 4 independently
> of the "size" argument.
>
> For example other project U-Boot has also pci-aardvark.c driver and
> U-Boot has for (probably same) purpose pci_get_ff() macro, see:
> https://source.denx.de/u-boot/u-boot/-/blob/v2021.10/drivers/pci/pci-aardvark.c#L367
>
> I'm not saying if current approach to always sets 0xffffffff
> (independently of "size" argument) is correct or not as I do not know
> it too! I'm just giving example that this PCI code has very similar
> implementation of other project (U-Boot) which sets number of ones based
> on the size argument.
>

I am not sure too, if we would like to have something like pci_get_ff()
which sets the return mask based on the size.

If we were to have something like pci_get_ff(), I can think of one
problem, some of the functions such as pci_raw_set_power_state() which
checks for errors does not have a "size" argument. An excerpt from that
function is as follows:
static int pci_raw_set_power_state(struct pci_dev *dev, pci_power_t state)
{
pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
if (pmcsr == (u16) ~0) {

For these functions we wont be able to use pci_get_ff(), I mean we could
definitely put the responsibility onto the programmers to write down the
correct size. But that might lead to mistakes, I guess?

Then for those cases, we might need to maintain both the
SET_PCI_ERROR_RESPONSE macro and the pci_get_ff() functions, which then
means that we might not have the same style for signalling config read
error.

I am pretty new to kernel development, so I am sure that whatever I said
above might be totally wrong. If so, please correct me :)

> So probably something for other people to decide.
>
> Anyway, I very like this your idea to have a macro which purpose is to
> explicitly indicate error during config read operation! And to unify all
> drivers to use same style for signalling config read error.
>

Thank you :D, I think I'll wait for other people to chime in here with
their opinions and then I'll redo the patch with whatever will be
decided.

Thank again for the detailed reply.

> > > > return PCIBIOS_DEVICE_NOT_FOUND;
> > > > }
> > > >
> > > > @@ -920,7 +920,7 @@ static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn,
> > > > *val = CFG_RD_CRS_VAL;
> > > > return PCIBIOS_SUCCESSFUL;
> > > > }
> > > > - *val = 0xffffffff;
> > > > + SET_PCI_ERROR_RESPONSE(val);
> > > > return PCIBIOS_SET_FAILED;
> > > > }
> > > >
> > > > @@ -955,14 +955,14 @@ static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn,
> > > > *val = CFG_RD_CRS_VAL;
> > > > return PCIBIOS_SUCCESSFUL;
> > > > }
> > > > - *val = 0xffffffff;
> > > > + SET_PCI_ERROR_RESPONSE(val);
> > > > return PCIBIOS_SET_FAILED;
> > > > }
> > > >
> > > > /* Check PIO status and get the read result */
> > > > ret = advk_pcie_check_pio_status(pcie, allow_crs, val);
> > > > if (ret < 0) {
> > > > - *val = 0xffffffff;
> > > > + SET_PCI_ERROR_RESPONSE(val);
> > > > return PCIBIOS_SET_FAILED;
> > > > }
> > > >
> > > > --
> > > > 2.25.1
> > > >

\
 
 \ /
  Last update: 2021-10-12 18:01    [W:1.318 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site