lkml.org 
[lkml]   [2020]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3 06/19] dt-bindings: usb: dwc3: Add a gpio-usb-connector description
On Wed, Jan 22, 2020 at 06:55:57PM +0000, Bryan O'Donoghue wrote:
> A USB connector should be a child node of the USB controller
> connector/usb-connector.txt. This patch adds a property
> "gpio_usb_connector" which declares a connector child device. Code in the
> DWC3 driver will then
>
> - Search for "gpio_usb_controller"
> - Do an of_platform_populate() if found
>
> This will have the effect of making the declared node a child of the USB
> controller and will make sure that USB role-switch events detected with the
> gpio_usb_controller driver propagate into the DWC3 controller code
> appropriately.

This is all driver specifics. This is a binding patch.

>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: linux-usb@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
> Documentation/devicetree/bindings/usb/dwc3.txt | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> index 66780a47ad85..b019bd472f83 100644
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
> @@ -108,6 +108,9 @@ Optional properties:
> When just one value, which means INCRX burst mode enabled. When
> more than one value, which means undefined length INCR burst type
> enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
> + - gpio_usb_connector: Declares a USB connector named 'gpio_usb_connector' as a
> + child node of the DWC3 block. Use when modelling a USB
> + connector based on the gpio-usb-b-connector driver.

Should be just 'connector'. That's already implicitly allowed for any
USB controller, so you don't really need a binding change. And the
specific type of connector is outside the scope of the DWC3 binding.

>
> - in addition all properties from usb-xhci.txt from the current directory are
> supported as well
> @@ -121,4 +124,12 @@ dwc3@4a030000 {
> interrupts = <0 92 4>
> usb-phy = <&usb2_phy>, <&usb3,phy>;
> snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> + usb_con: gpio_usb_connector {
> + compatible = "gpio-usb-b-connector";
> + id-gpio = <&tlmm 116 GPIO_ACTIVE_HIGH>;
> + vbus-gpio = <&pms405_gpios 12 GPIO_ACTIVE_HIGH>;

*-gpios is the preferred form and should be what's documented.

> + vbus-supply = <&usb3_vbus_reg>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
> + };
> };
> --
> 2.25.0
>

\
 
 \ /
  Last update: 2020-01-27 19:44    [W:0.183 / U:0.552 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site