lkml.org 
[lkml]   [2019]   [Feb]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next 3/7] net: phy: marvell10g: Use 2500BASEX when using 2.5GBASET
Date
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.

Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.

At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.

This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
drivers/net/phy/marvell10g.c | 26 +++++++++++++++++++-------
1 file changed, 19 insertions(+), 7 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 8e2d6039b9b3..127200a8cf9b 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -235,6 +235,7 @@ static int mv3310_config_init(struct phy_device *phydev)
{
/* Check that the PHY interface type is compatible */
if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
+ phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
phydev->interface != PHY_INTERFACE_MODE_XAUI &&
phydev->interface != PHY_INTERFACE_MODE_RXAUI &&
phydev->interface != PHY_INTERFACE_MODE_10GKR)
@@ -325,18 +326,29 @@ static int mv3310_aneg_done(struct phy_device *phydev)
static void mv3310_update_interface(struct phy_device *phydev)
{
if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||
+ phydev->interface == PHY_INTERFACE_MODE_2500BASEX ||
phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {
/* The PHY automatically switches its serdes interface (and
- * active PHYXS instance) between Cisco SGMII and 10GBase-KR
- * modes according to the speed. Florian suggests setting
- * phydev->interface to communicate this to the MAC. Only do
- * this if we are already in either SGMII or 10GBase-KR mode.
+ * active PHYXS instance) between Cisco SGMII, 10GBase-KR and
+ * 2500BaseX modes according to the speed. Florian suggests
+ * setting phydev->interface to communicate this to the MAC.
+ * Only do this if we are already in one of the above modes.
*/
- if (phydev->speed == SPEED_10000)
+ switch (phydev->speed) {
+ case SPEED_10000:
phydev->interface = PHY_INTERFACE_MODE_10GKR;
- else if (phydev->speed >= SPEED_10 &&
- phydev->speed < SPEED_10000)
+ break;
+ case SPEED_2500:
+ phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+ break;
+ case SPEED_1000:
+ case SPEED_100:
+ case SPEED_10:
phydev->interface = PHY_INTERFACE_MODE_SGMII;
+ break;
+ default:
+ break;
+ }
}
}

--
2.19.2
\
 
 \ /
  Last update: 2019-02-21 10:52    [W:0.071 / U:0.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site