lkml.org 
[lkml]   [2019]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 8/9] arm64: dts: rockchip: RockPro64: enable wifi module at sdio0
Date
RockPro64 supports an Ampak AP6359SA based wifi/bt combo module.
The BCM4359/9 wifi controller in this module is connected to sdio0,
enable this interface.

Use the in-band sdio irq instead of the out-of-band wifi_host_wake_l
signal since the latter is not working reliably on this board (probably
due to it's PCIe WAKE# connection).

Signed-off-by: Soeren Moch <smoch@web.de>
---
changes in v2:
- add comment about irq in commit message

Not sure where to place exactly the sdio0 node in the dts because
existing sd nodes are not sorted alphabetically.

Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
.../boot/dts/rockchip/rk3399-rockpro64.dts | 21 ++++++++++++-------
1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
index 7f4b2eba31d4..9fa92790d6e0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
@@ -71,13 +71,6 @@
clock-names = "ext_clock";
pinctrl-names = "default";
pinctrl-0 = <&wifi_enable_h>;
-
- /*
- * On the module itself this is one of these (depending
- * on the actual card populated):
- * - SDIO_RESET_L_WL_REG_ON
- * - PDN (power down when low)
- */
reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
};

@@ -650,6 +643,20 @@
status = "okay";
};

+&sdio0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ disable-wp;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
&sdmmc {
bus-width = <4>;
cap-sd-highspeed;
--
2.17.1
\
 
 \ /
  Last update: 2019-12-12 00:54    [W:0.136 / U:0.144 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site