lkml.org 
[lkml]   [2019]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 9/9] arm64: dts: rockchip: RockPro64: hook up bluetooth at uart0
Date
With enabled wifi support (required for firmware loading) for the
Ampak AP6359SA based wifi/bt combo module we now also can enable
the bluetooth part.

Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Soeren Moch <smoch@web.de>
---
changes in v2:
- new patch

Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
.../boot/dts/rockchip/rk3399-rockpro64.dts | 29 ++++++++++++++++++-
1 file changed, 28 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
index 9fa92790d6e0..94cc462e234d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts
@@ -561,6 +561,20 @@
};

&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
buttons {
pwrbtn: pwrbtn {
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -729,8 +743,21 @@

&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_xfer &uart0_cts>;
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rk808 1>;
+ clock-names = "extclk";
+ device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+ };
};

&uart2 {
--
2.17.1
\
 
 \ /
  Last update: 2019-12-12 00:54    [W:0.181 / U:0.228 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site