lkml.org 
[lkml]   [2018]   [Apr]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] net: phy: marvell: Enable interrupt function on LED2 pin
Date
From: Esben Haabendal <eha@deif.com>

The LED2[2]/INTn pin on Marvell 88E1318S as well as 88E1510/12/14/18 needs
to be configured to be usable as interrupt not only when WOL is enabled,
but whenever we rely on interrupts from the PHY.

Signed-off-by: Esben Haabendal <eha@deif.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
---
drivers/net/phy/marvell.c | 19 +++++++++++++++++--
1 file changed, 17 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 0e0978d8a0eb..f03a510f1247 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -457,6 +457,21 @@ static int marvell_of_reg_init(struct phy_device *phydev)
}
#endif /* CONFIG_OF_MDIO */

+static int m88e1318_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ err = marvell_config_intr(phydev);
+ if (err)
+ return err;
+
+ /* Setup LED[2] as interrupt pin (active low) */
+ return phy_modify(phydev, MII_88E1318S_PHY_LED_TCR,
+ MII_88E1318S_PHY_LED_TCR_FORCE_INT,
+ MII_88E1318S_PHY_LED_TCR_INTn_ENABLE |
+ MII_88E1318S_PHY_LED_TCR_INT_ACTIVE_LOW);
+}
+
static int m88e1121_config_aneg_rgmii_delays(struct phy_device *phydev)
{
int mscr;
@@ -2090,7 +2105,7 @@ static struct phy_driver marvell_drivers[] = {
.config_aneg = &m88e1318_config_aneg,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
- .config_intr = &marvell_config_intr,
+ .config_intr = &m88e1318_config_intr,
.did_interrupt = &m88e1121_did_interrupt,
.get_wol = &m88e1318_get_wol,
.set_wol = &m88e1318_set_wol,
@@ -2189,7 +2204,7 @@ static struct phy_driver marvell_drivers[] = {
.config_aneg = &m88e1510_config_aneg,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
- .config_intr = &marvell_config_intr,
+ .config_intr = &m88e1318_config_intr,
.did_interrupt = &m88e1121_did_interrupt,
.get_wol = &m88e1318_get_wol,
.set_wol = &m88e1318_set_wol,
--
2.16.3
\
 
 \ /
  Last update: 2018-04-05 15:36    [W:0.401 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site