lkml.org 
[lkml]   [2018]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] hwmon/sch5627: Use common error handling code in sch5627_probe()
From
Date
Hi,

On 12-03-18 22:23, SF Markus Elfring wrote:
> From: Markus Elfring <elfring@users.sourceforge.net>
> Date: Mon, 12 Mar 2018 22:15:59 +0100
>
> Adjust jump targets so that a bit of exception handling can be better
> reused at the end of this function.
>
> This issue was detected by using the Coccinelle software.
>
> Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>

So now we have a goto set_error_code with the code at the set_error_code
doing something and then doing another goto. No, just no. goto-s going to
a label calling another goto is completely unreadable.

I really do not see any reason for the proposed changes, they may remove
a small amount of code duplication, but at a hugh cost wrt readability.

TL;DR: NACK

Regards,

Hans



> ---
> drivers/hwmon/sch5627.c | 60 ++++++++++++++++++++++++-------------------------
> 1 file changed, 29 insertions(+), 31 deletions(-)
>
> diff --git a/drivers/hwmon/sch5627.c b/drivers/hwmon/sch5627.c
> index 91544f2312e6..e7a2a974ab74 100644
> --- a/drivers/hwmon/sch5627.c
> +++ b/drivers/hwmon/sch5627.c
> @@ -480,72 +480,64 @@ static int sch5627_probe(struct platform_device *pdev)
> platform_set_drvdata(pdev, data);
>
> val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_HWMON_ID);
> - if (val < 0) {
> - err = val;
> - goto error;
> - }
> + if (val < 0)
> + goto set_error_code;
> +
> if (val != SCH5627_HWMON_ID) {
> pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "hwmon",
> val, SCH5627_HWMON_ID);
> - err = -ENODEV;
> - goto error;
> + goto e_nodev;
> }
>
> val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_COMPANY_ID);
> - if (val < 0) {
> - err = val;
> - goto error;
> - }
> + if (val < 0)
> + goto set_error_code;
> +
> if (val != SCH5627_COMPANY_ID) {
> pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "company",
> val, SCH5627_COMPANY_ID);
> - err = -ENODEV;
> - goto error;
> + goto e_nodev;
> }
>
> val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_PRIMARY_ID);
> - if (val < 0) {
> - err = val;
> - goto error;
> - }
> + if (val < 0)
> + goto set_error_code;
> +
> if (val != SCH5627_PRIMARY_ID) {
> pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "primary",
> val, SCH5627_PRIMARY_ID);
> - err = -ENODEV;
> - goto error;
> + goto e_nodev;
> }
>
> build_code = sch56xx_read_virtual_reg(data->addr,
> SCH5627_REG_BUILD_CODE);
> if (build_code < 0) {
> err = build_code;
> - goto error;
> + goto remove_device;
> }
>
> build_id = sch56xx_read_virtual_reg16(data->addr,
> SCH5627_REG_BUILD_ID);
> if (build_id < 0) {
> err = build_id;
> - goto error;
> + goto remove_device;
> }
>
> hwmon_rev = sch56xx_read_virtual_reg(data->addr,
> SCH5627_REG_HWMON_REV);
> if (hwmon_rev < 0) {
> err = hwmon_rev;
> - goto error;
> + goto remove_device;
> }
>
> val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_CTRL);
> - if (val < 0) {
> - err = val;
> - goto error;
> - }
> + if (val < 0)
> + goto set_error_code;
> +
> data->control = val;
> if (!(data->control & 0x01)) {
> pr_err("hardware monitoring not enabled\n");
> - err = -ENODEV;
> - goto error;
> + goto e_nodev;
> }
> /* Trigger a Vbat voltage measurement, so that we get a valid reading
> the first time we read Vbat */
> @@ -559,7 +551,7 @@ static int sch5627_probe(struct platform_device *pdev)
> */
> err = sch5627_read_limits(data);
> if (err)
> - goto error;
> + goto remove_device;
>
> pr_info("found %s chip at %#hx\n", DEVNAME, data->addr);
> pr_info("firmware build: code 0x%02X, id 0x%04X, hwmon: rev 0x%02X\n",
> @@ -568,13 +560,13 @@ static int sch5627_probe(struct platform_device *pdev)
> /* Register sysfs interface files */
> err = sysfs_create_group(&pdev->dev.kobj, &sch5627_group);
> if (err)
> - goto error;
> + goto remove_device;
>
> data->hwmon_dev = hwmon_device_register(&pdev->dev);
> if (IS_ERR(data->hwmon_dev)) {
> err = PTR_ERR(data->hwmon_dev);
> data->hwmon_dev = NULL;
> - goto error;
> + goto remove_device;
> }
>
> /* Note failing to register the watchdog is not a fatal error */
> @@ -584,7 +576,13 @@ static int sch5627_probe(struct platform_device *pdev)
>
> return 0;
>
> -error:
> +set_error_code:
> + err = val;
> + goto remove_device;
> +
> +e_nodev:
> + err = -ENODEV;
> +remove_device:
> sch5627_remove(pdev);
> return err;
> }
>

\
 
 \ /
  Last update: 2018-03-13 09:20    [W:0.070 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site