lkml.org 
[lkml]   [2018]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] hwmon/sch5627: Use common error handling code in sch5627_probe()
On Tue, Mar 13, 2018 at 09:19:22AM +0100, Hans de Goede wrote:
> Hi,
>
> On 12-03-18 22:23, SF Markus Elfring wrote:
> >From: Markus Elfring <elfring@users.sourceforge.net>
> >Date: Mon, 12 Mar 2018 22:15:59 +0100
> >
> >Adjust jump targets so that a bit of exception handling can be better
> >reused at the end of this function.
> >
> >This issue was detected by using the Coccinelle software.
> >
> >Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
>
> So now we have a goto set_error_code with the code at the set_error_code
> doing something and then doing another goto. No, just no. goto-s going to
> a label calling another goto is completely unreadable.
>
> I really do not see any reason for the proposed changes, they may remove
> a small amount of code duplication, but at a hugh cost wrt readability.
>
> TL;DR: NACK
>
Fully agree. NACK confirmed.

Guenter

> Regards,
>
> Hans
>
>
>
> >---
> > drivers/hwmon/sch5627.c | 60 ++++++++++++++++++++++++-------------------------
> > 1 file changed, 29 insertions(+), 31 deletions(-)
> >
> >diff --git a/drivers/hwmon/sch5627.c b/drivers/hwmon/sch5627.c
> >index 91544f2312e6..e7a2a974ab74 100644
> >--- a/drivers/hwmon/sch5627.c
> >+++ b/drivers/hwmon/sch5627.c
> >@@ -480,72 +480,64 @@ static int sch5627_probe(struct platform_device *pdev)
> > platform_set_drvdata(pdev, data);
> > val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_HWMON_ID);
> >- if (val < 0) {
> >- err = val;
> >- goto error;
> >- }
> >+ if (val < 0)
> >+ goto set_error_code;
> >+
> > if (val != SCH5627_HWMON_ID) {
> > pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "hwmon",
> > val, SCH5627_HWMON_ID);
> >- err = -ENODEV;
> >- goto error;
> >+ goto e_nodev;
> > }
> > val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_COMPANY_ID);
> >- if (val < 0) {
> >- err = val;
> >- goto error;
> >- }
> >+ if (val < 0)
> >+ goto set_error_code;
> >+
> > if (val != SCH5627_COMPANY_ID) {
> > pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "company",
> > val, SCH5627_COMPANY_ID);
> >- err = -ENODEV;
> >- goto error;
> >+ goto e_nodev;
> > }
> > val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_PRIMARY_ID);
> >- if (val < 0) {
> >- err = val;
> >- goto error;
> >- }
> >+ if (val < 0)
> >+ goto set_error_code;
> >+
> > if (val != SCH5627_PRIMARY_ID) {
> > pr_err("invalid %s id: 0x%02X (expected 0x%02X)\n", "primary",
> > val, SCH5627_PRIMARY_ID);
> >- err = -ENODEV;
> >- goto error;
> >+ goto e_nodev;
> > }
> > build_code = sch56xx_read_virtual_reg(data->addr,
> > SCH5627_REG_BUILD_CODE);
> > if (build_code < 0) {
> > err = build_code;
> >- goto error;
> >+ goto remove_device;
> > }
> > build_id = sch56xx_read_virtual_reg16(data->addr,
> > SCH5627_REG_BUILD_ID);
> > if (build_id < 0) {
> > err = build_id;
> >- goto error;
> >+ goto remove_device;
> > }
> > hwmon_rev = sch56xx_read_virtual_reg(data->addr,
> > SCH5627_REG_HWMON_REV);
> > if (hwmon_rev < 0) {
> > err = hwmon_rev;
> >- goto error;
> >+ goto remove_device;
> > }
> > val = sch56xx_read_virtual_reg(data->addr, SCH5627_REG_CTRL);
> >- if (val < 0) {
> >- err = val;
> >- goto error;
> >- }
> >+ if (val < 0)
> >+ goto set_error_code;
> >+
> > data->control = val;
> > if (!(data->control & 0x01)) {
> > pr_err("hardware monitoring not enabled\n");
> >- err = -ENODEV;
> >- goto error;
> >+ goto e_nodev;
> > }
> > /* Trigger a Vbat voltage measurement, so that we get a valid reading
> > the first time we read Vbat */
> >@@ -559,7 +551,7 @@ static int sch5627_probe(struct platform_device *pdev)
> > */
> > err = sch5627_read_limits(data);
> > if (err)
> >- goto error;
> >+ goto remove_device;
> > pr_info("found %s chip at %#hx\n", DEVNAME, data->addr);
> > pr_info("firmware build: code 0x%02X, id 0x%04X, hwmon: rev 0x%02X\n",
> >@@ -568,13 +560,13 @@ static int sch5627_probe(struct platform_device *pdev)
> > /* Register sysfs interface files */
> > err = sysfs_create_group(&pdev->dev.kobj, &sch5627_group);
> > if (err)
> >- goto error;
> >+ goto remove_device;
> > data->hwmon_dev = hwmon_device_register(&pdev->dev);
> > if (IS_ERR(data->hwmon_dev)) {
> > err = PTR_ERR(data->hwmon_dev);
> > data->hwmon_dev = NULL;
> >- goto error;
> >+ goto remove_device;
> > }
> > /* Note failing to register the watchdog is not a fatal error */
> >@@ -584,7 +576,13 @@ static int sch5627_probe(struct platform_device *pdev)
> > return 0;
> >-error:
> >+set_error_code:
> >+ err = val;
> >+ goto remove_device;
> >+
> >+e_nodev:
> >+ err = -ENODEV;
> >+remove_device:
> > sch5627_remove(pdev);
> > return err;
> > }
> >

\
 
 \ /
  Last update: 2018-03-13 17:01    [W:0.076 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site