lkml.org 
[lkml]   [2018]   [Feb]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 2/2] dt-bindings: Document the Rockchip RK1608 bindings
Date
From: Leo Wen <leo.wen@rock-chips.com>

Add DT bindings documentation for Rockchip RK1608.

Changes V2:
- Delete spi-min-frequency property.
- Add the external sensor's control pin and clock properties.
- Delete the '&pinctrl' node.

Signed-off-by: Leo Wen <leo.wen@rock-chips.com>
---
Documentation/devicetree/bindings/media/rk1608.txt | 97 ++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 98 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/rk1608.txt

diff --git a/Documentation/devicetree/bindings/media/rk1608.txt b/Documentation/devicetree/bindings/media/rk1608.txt
new file mode 100644
index 0000000..a9721a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/rk1608.txt
@@ -0,0 +1,97 @@
+Rockchip RK1608 as a PreISP to link on Soc
+------------------------------------------
+
+Required properties:
+
+- compatible : "rockchip,rk1608";
+- reg : SPI slave address of the rk1608;
+- clocks : Must contain an entry for each entry in clock-names;
+- clock-names : Must contain "mclk" for the device's master clock;
+- reset-gpio : GPIO connected to reset pin;
+- irq-gpio : GPIO connected to irq pin;
+- sleepst-gpio : GPIO connected to sleepst pin;
+- wakeup-gpio : GPIO connected to wakeup pin;
+- powerdown-gpio : GPIO connected to powerdown pin;
+- rockchip,powerdown0 : GPIO connected to the sensor0's powerdown pin;
+- rockchip,reset0 : GPIO connected to the sensor0's reset pin;
+- rockchip,powerdown1 : GPIO connected to the sensor1's powerdown pin;
+- rockchip,reset1 : GPIO connected to the sensor1's reset pin;
+- pinctrl-names : Should contain only one value - "default";
+- pinctrl-0 : Pin control group to be used for this controller;
+
+Optional properties:
+
+- spi-max-frequency : Maximum SPI clocking speed of the device;
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt. The following are properties specific to those
+nodes.
+
+endpoint node
+-------------
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+ video-interfaces.txt. If present it should be <1> - the device
+ supports only one data lane without re-mapping.
+
+Note1: Since no data is generated in RK1608,so this is meaningful that you need
+a extra sensor (such as a camera) mounted on RK1608. You need to use endpoint@x
+to match these sensors.
+
+Note2:You must set the current value of the spi pins to be 8mA, if they are not.
+
+Example:
+&spi0 {
+ status = "okay";
+ spi_rk1608@00 {
+ compatible = "rockchip,rk1608";
+ status = "okay";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ link-freqs = /bits/ 64 <400000000>;
+ clocks = <&cru SCLK_SPI0>, <&cru SCLK_VIP_OUT>,
+ <&cru DCLK_VOP0>, <&cru ACLK_VIP>, <&cru HCLK_VIP>,
+ <&cru PCLK_ISP_IN>, <&cru PCLK_ISP_IN>,
+ <&cru PCLK_ISP_IN>, <&cru SCLK_MIPIDSI_24M>,
+ <&cru PCLK_MIPI_CSI>;
+ clock-names = "mclk", "mipi_clk", "pd_cif", "aclk_cif",
+ "hclk_cif", "cif0_in", "g_pclkin_cif",
+ "cif0_out", "clk_mipi_24m", "hclk_mipiphy";
+ reset-gpio = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+ irq-gpio = <&gpio6 2 GPIO_ACTIVE_HIGH>;
+ sleepst-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+ wakeup-gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
+ powerdown-gpio = <&gpio8 0 GPIO_ACTIVE_HIGH>;
+
+ rockchip,powerdown1 = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ rockchip,reset1 = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+
+ rockchip,powerdown0 = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+ rockchip,reset0 = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&rk1608_irq_gpios &rk1608_wake_gpios
+ &rk1608_sleep_gpios>;
+
+ port@0 {
+ mipi_dphy_out: endpoint {
+ remote-endpoint = <&mipi_dphy_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ clock-noncontinuous;
+ link-frequencies =
+ /bits/ 64 <400000000>;
+ };
+ };
+ /* Example: we have two cameras */
+ port@1 {
+ sensor_in0: endpoint@0 {
+ remote-endpoint = <&sensor_out0>;
+ };
+ sensor_in1: endpoint@1 {
+ remote-endpoint = <&sensor_out1>;
+ };
+ };
+ };
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index b2a98e3..04d227b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -141,6 +141,7 @@ M: Leo Wen <leo.wen@rock-chips.com>
S: Maintained
F: drivers/media/spi/rk1608.c
F: drivers/media/spi/rk1608.h
+F: Documentation/devicetree/bindings/media/rk1608.txt

3C59X NETWORK DRIVER
M: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
--
2.7.4

\
 
 \ /
  Last update: 2018-02-26 09:31    [W:0.054 / U:0.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site