lkml.org 
[lkml]   [2018]   [Mar]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2 2/2] dt-bindings: Document the Rockchip RK1608 bindings
Hi Wen,

On Mon, Feb 26, 2018 at 04:25:04PM +0800, Wen Nuan wrote:
> From: Leo Wen <leo.wen@rock-chips.com>
>
> Add DT bindings documentation for Rockchip RK1608.
>
> Changes V2:
> - Delete spi-min-frequency property.
> - Add the external sensor's control pin and clock properties.
> - Delete the '&pinctrl' node.
>
> Signed-off-by: Leo Wen <leo.wen@rock-chips.com>
> ---
> Documentation/devicetree/bindings/media/rk1608.txt | 97 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 98 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/rk1608.txt
>
> diff --git a/Documentation/devicetree/bindings/media/rk1608.txt b/Documentation/devicetree/bindings/media/rk1608.txt
> new file mode 100644
> index 0000000..a9721a8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/rk1608.txt
> @@ -0,0 +1,97 @@
> +Rockchip RK1608 as a PreISP to link on Soc
> +------------------------------------------
> +
> +Required properties:
> +
> +- compatible : "rockchip,rk1608";
> +- reg : SPI slave address of the rk1608;
> +- clocks : Must contain an entry for each entry in clock-names;
> +- clock-names : Must contain "mclk" for the device's master clock;
> +- reset-gpio : GPIO connected to reset pin;
> +- irq-gpio : GPIO connected to irq pin;
> +- sleepst-gpio : GPIO connected to sleepst pin;
> +- wakeup-gpio : GPIO connected to wakeup pin;
> +- powerdown-gpio : GPIO connected to powerdown pin;
> +- rockchip,powerdown0 : GPIO connected to the sensor0's powerdown pin;
> +- rockchip,reset0 : GPIO connected to the sensor0's reset pin;
> +- rockchip,powerdown1 : GPIO connected to the sensor1's powerdown pin;
> +- rockchip,reset1 : GPIO connected to the sensor1's reset pin;

Aren't these sensor's properties and not related to the ISP?

> +- pinctrl-names : Should contain only one value - "default";
> +- pinctrl-0 : Pin control group to be used for this controller;
> +
> +Optional properties:
> +
> +- spi-max-frequency : Maximum SPI clocking speed of the device;
> +
> +The device node should contain one 'port' child node with one child 'endpoint'
> +node, according to the bindings defined in Documentation/devicetree/bindings/
> +media/video-interfaces.txt. The following are properties specific to those
> +nodes.
> +
> +endpoint node
> +-------------
> +
> +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
> + video-interfaces.txt. If present it should be <1> - the device
> + supports only one data lane without re-mapping.
> +
> +Note1: Since no data is generated in RK1608,so this is meaningful that you need
> +a extra sensor (such as a camera) mounted on RK1608. You need to use endpoint@x
> +to match these sensors.
> +
> +Note2:You must set the current value of the spi pins to be 8mA, if they are not.
> +
> +Example:
> +&spi0 {
> + status = "okay";
> + spi_rk1608@00 {
> + compatible = "rockchip,rk1608";
> + status = "okay";
> + reg = <0>;
> + spi-max-frequency = <24000000>;
> + link-freqs = /bits/ 64 <400000000>;
> + clocks = <&cru SCLK_SPI0>, <&cru SCLK_VIP_OUT>,
> + <&cru DCLK_VOP0>, <&cru ACLK_VIP>, <&cru HCLK_VIP>,
> + <&cru PCLK_ISP_IN>, <&cru PCLK_ISP_IN>,
> + <&cru PCLK_ISP_IN>, <&cru SCLK_MIPIDSI_24M>,
> + <&cru PCLK_MIPI_CSI>;
> + clock-names = "mclk", "mipi_clk", "pd_cif", "aclk_cif",
> + "hclk_cif", "cif0_in", "g_pclkin_cif",
> + "cif0_out", "clk_mipi_24m", "hclk_mipiphy";
> + reset-gpio = <&gpio6 0 GPIO_ACTIVE_HIGH>;
> + irq-gpio = <&gpio6 2 GPIO_ACTIVE_HIGH>;
> + sleepst-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
> + wakeup-gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
> + powerdown-gpio = <&gpio8 0 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,powerdown1 = <&gpio5 9 GPIO_ACTIVE_HIGH>;
> + rockchip,reset1 = <&gpio6 8 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,powerdown0 = <&gpio5 8 GPIO_ACTIVE_HIGH>;
> + rockchip,reset0 = <&gpio6 7 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&rk1608_irq_gpios &rk1608_wake_gpios
> + &rk1608_sleep_gpios>;
> +
> + port@0 {
> + mipi_dphy_out: endpoint {
> + remote-endpoint = <&mipi_dphy_in>;
> + clock-lanes = <0>;
> + data-lanes = <1 2 3 4>;
> + clock-noncontinuous;
> + link-frequencies =
> + /bits/ 64 <400000000>;
> + };
> + };
> + /* Example: we have two cameras */

What determines which one is active? The documentation above states there
may only be a single endpoint per port. And a single port only, not two as
you have here.

> + port@1 {
> + sensor_in0: endpoint@0 {
> + remote-endpoint = <&sensor_out0>;
> + };
> + sensor_in1: endpoint@1 {
> + remote-endpoint = <&sensor_out1>;
> + };
> + };
> + };
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index b2a98e3..04d227b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -141,6 +141,7 @@ M: Leo Wen <leo.wen@rock-chips.com>
> S: Maintained
> F: drivers/media/spi/rk1608.c
> F: drivers/media/spi/rk1608.h
> +F: Documentation/devicetree/bindings/media/rk1608.txt
>
> 3C59X NETWORK DRIVER
> M: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>

--
Regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi

\
 
 \ /
  Last update: 2018-03-07 10:53    [W:0.046 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site