lkml.org 
[lkml]   [2015]   [Jul]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/2] media: atmel-isi: setup the ISI_CFG2 register directly
Date
Hi Josh,

Thank you for the patch.

On Wednesday 17 June 2015 18:39:38 Josh Wu wrote:
> In the function configure_geometry(), we will setup the ISI CFG2
> according to the sensor output format.
>
> It make no sense to just read back the CFG2 register and just set part
> of it.
>
> So just set up this register directly makes things simpler.
> Currently only support YUV format from camera sensor.
>
> Signed-off-by: Josh Wu <josh.wu@atmel.com>

The default value of the register is all 0 so this should be good.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>
> drivers/media/platform/soc_camera/atmel-isi.c | 20 +++++++-------------
> 1 file changed, 7 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
> b/drivers/media/platform/soc_camera/atmel-isi.c index 9070172..8bc40ca
> 100644
> --- a/drivers/media/platform/soc_camera/atmel-isi.c
> +++ b/drivers/media/platform/soc_camera/atmel-isi.c
> @@ -105,24 +105,25 @@ static u32 isi_readl(struct atmel_isi *isi, u32 reg)
> static int configure_geometry(struct atmel_isi *isi, u32 width,
> u32 height, u32 code)
> {
> - u32 cfg2, cr;
> + u32 cfg2;
>
> + /* According to sensor's output format to set cfg2 */
> switch (code) {
> /* YUV, including grey */
> case MEDIA_BUS_FMT_Y8_1X8:
> - cr = ISI_CFG2_GRAYSCALE;
> + cfg2 = ISI_CFG2_GRAYSCALE;
> break;
> case MEDIA_BUS_FMT_VYUY8_2X8:
> - cr = ISI_CFG2_YCC_SWAP_MODE_3;
> + cfg2 = ISI_CFG2_YCC_SWAP_MODE_3;
> break;
> case MEDIA_BUS_FMT_UYVY8_2X8:
> - cr = ISI_CFG2_YCC_SWAP_MODE_2;
> + cfg2 = ISI_CFG2_YCC_SWAP_MODE_2;
> break;
> case MEDIA_BUS_FMT_YVYU8_2X8:
> - cr = ISI_CFG2_YCC_SWAP_MODE_1;
> + cfg2 = ISI_CFG2_YCC_SWAP_MODE_1;
> break;
> case MEDIA_BUS_FMT_YUYV8_2X8:
> - cr = ISI_CFG2_YCC_SWAP_DEFAULT;
> + cfg2 = ISI_CFG2_YCC_SWAP_DEFAULT;
> break;
> /* RGB, TODO */
> default:
> @@ -130,17 +131,10 @@ static int configure_geometry(struct atmel_isi *isi,
> u32 width, }
>
> isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
> -
> - cfg2 = isi_readl(isi, ISI_CFG2);
> - /* Set YCC swap mode */
> - cfg2 &= ~ISI_CFG2_YCC_SWAP_MODE_MASK;
> - cfg2 |= cr;
> /* Set width */
> - cfg2 &= ~(ISI_CFG2_IM_HSIZE_MASK);
> cfg2 |= ((width - 1) << ISI_CFG2_IM_HSIZE_OFFSET) &
> ISI_CFG2_IM_HSIZE_MASK;
> /* Set height */
> - cfg2 &= ~(ISI_CFG2_IM_VSIZE_MASK);
> cfg2 |= ((height - 1) << ISI_CFG2_IM_VSIZE_OFFSET)
> & ISI_CFG2_IM_VSIZE_MASK;
> isi_writel(isi, ISI_CFG2, cfg2);

--
Regards,

Laurent Pinchart



\
 
 \ /
  Last update: 2015-07-31 17:01    [W:0.092 / U:0.784 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site