lkml.org 
[lkml]   [2024]   [Mar]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 1/1] dt-bindings: net: dwmac: Document STM32 property st,ext-phyclk

On Thu, 28 Mar 2024 15:08:03 +0100, Christophe Roullier wrote:
> The Linux kernel dwmac-stm32 driver currently supports three DT
> properties used to configure whether PHY clock are generated by
> the MAC or supplied to the MAC from the PHY.
>
> Originally there were two properties, st,eth-clk-sel and
> st,eth-ref-clk-sel, each used to configure MAC clocking in
> different bus mode and for different MAC clock frequency.
> Since it is possible to determine the MAC 'eth-ck' clock
> frequency from the clock subsystem and PHY bus mode from
> the 'phy-mode' property, two disparate DT properties are
> no longer required to configure MAC clocking.
>
> Linux kernel commit 1bb694e20839 ("net: ethernet: stmmac: simplify phy modes management for stm32")
> introduced a third, unified, property st,ext-phyclk. This property
> covers both use cases of st,eth-clk-sel and st,eth-ref-clk-sel DT
> properties, as well as a new use case for 25 MHz clock generated
> by the MAC.
>
> The third property st,ext-phyclk is so far undocumented,
> document it.
>
> Below table summarizes the clock requirement and clock sources for
> supported PHY interface modes.
> __________________________________________________________________________
> |PHY_MODE | Normal | PHY wo crystal| PHY wo crystal |No 125Mhz from PHY|
> | | | 25MHz | 50MHz | |
>
> ---------------------------------------------------------------------------
> | MII | - | eth-ck | n/a | n/a |
> | | | st,ext-phyclk | | |
>
> ---------------------------------------------------------------------------
> | GMII | - | eth-ck | n/a | n/a |
> | | | st,ext-phyclk | | |
>
> ---------------------------------------------------------------------------
> | RGMII | - | eth-ck | n/a | eth-ck |
> | | | st,ext-phyclk | | st,eth-clk-sel or|
> | | | | | st,ext-phyclk |
>
> ---------------------------------------------------------------------------
> | RMII | - | eth-ck | eth-ck | n/a |
> | | | st,ext-phyclk | st,eth-ref-clk-sel | |
> | | | | or st,ext-phyclk | |
>
> ---------------------------------------------------------------------------
>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
> ---
> Documentation/devicetree/bindings/net/stm32-dwmac.yaml | 7 +++++++
> 1 file changed, 7 insertions(+)
>

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:
/Documentation/devicetree/bindings/net/stm32-dwmac.yaml:86:5: [warning] wrong indentation: expected 2 but found 4 (indentation)
/Documentation/devicetree/bindings/net/stm32-dwmac.yaml:92:3: [error] syntax error: expected <block end>, but found '<block mapping start>' (syntax)

dtschema/dtc warnings/errors:
make[2]: *** Deleting file 'Documentation/devicetree/bindings/net/stm32-dwmac.example.dts'
Documentation/devicetree/bindings/net/stm32-dwmac.yaml:92:3: did not find expected key
make[2]: *** [Documentation/devicetree/bindings/Makefile:26: Documentation/devicetree/bindings/net/stm32-dwmac.example.dts] Error 1
make[2]: *** Waiting for unfinished jobs....
/Documentation/devicetree/bindings/net/stm32-dwmac.yaml:92:3: did not find expected key
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml: ignoring, error parsing file
make[1]: *** [/builds/robherring/dt-review-ci/linux/Makefile:1430: dt_binding_check] Error 2
make: *** [Makefile:240: __sub-make] Error 2

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240328140803.324141-2-christophe.roullier@foss.st.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.


\
 
 \ /
  Last update: 2024-03-28 16:26    [W:0.066 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site