lkml.org 
[lkml]   [2023]   [Aug]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] hwmon: (pmbus/bel-pfe) Enable PMBUS_SKIP_STATUS_CHECK for pfe1100
Hi Guenter,

Thank you for the quick review, and I've addressed your comments in v2.


Cheers,
Tao

On Fri, Aug 04, 2023 at 08:19:40AM -0700, Guenter Roeck wrote:
> On 8/3/23 16:55, rentao.bupt@gmail.com wrote:
> > From: Tao Ren <rentao.bupt@gmail.com>
> >
> > Enable PMBUS_SKIP_STATUS_CHECK flag for both pfe1100 and pfe3000 because
> > the similar communication error is observed on pfe1100 devices.
> >
> > Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
> > ---
> > drivers/hwmon/pmbus/bel-pfe.c | 6 +++---
> > 1 file changed, 3 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/hwmon/pmbus/bel-pfe.c b/drivers/hwmon/pmbus/bel-pfe.c
> > index fa5070ae26bc..8280d274da3f 100644
> > --- a/drivers/hwmon/pmbus/bel-pfe.c
> > +++ b/drivers/hwmon/pmbus/bel-pfe.c
> > @@ -17,12 +17,12 @@
> > enum chips {pfe1100, pfe3000};
> > /*
> > - * Disable status check for pfe3000 devices, because some devices report
> > + * Disable status check for pfexxxx devices, because some devices report
> > * communication error (invalid command) for VOUT_MODE command (0x20)
> > * although correct VOUT_MODE (0x16) is returned: it leads to incorrect
> > * exponent in linear mode.
> > */
>
> Rephrase to something like
>
> Disable status check because some devices ... linear mode.
> This affects both pfe3000 and pfe1100.
>
> We don't know if other pfe devices will be supported by the driver in the
> future, and we don't know if those will be affected, so we should not make
> any claims about such devices.
>
> > -static struct pmbus_platform_data pfe3000_plat_data = {
> > +static struct pmbus_platform_data pfe_plat_data = {
> > .flags = PMBUS_SKIP_STATUS_CHECK,
> > };
> > @@ -94,6 +94,7 @@ static int pfe_pmbus_probe(struct i2c_client *client)
> > int model;
> > model = (int)i2c_match_id(pfe_device_id, client)->driver_data;
> > + client->dev.platform_data = &pfe_plat_data;
> > /*
> > * PFE3000-12-069RA devices may not stay in page 0 during device
> > @@ -101,7 +102,6 @@ static int pfe_pmbus_probe(struct i2c_client *client)
> > * So let's set the device to page 0 at the beginning.
> > */
> > if (model == pfe3000) {
> > - client->dev.platform_data = &pfe3000_plat_data;
> > i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
> > }
>
> { } is no longer needed.
>
> Thanks,
> Guenter
>

\
 
 \ /
  Last update: 2023-08-05 00:18    [W:0.037 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site