lkml.org 
[lkml]   [2023]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v3 2/3] drm/msm/dpu: use dpu core's major version to enable data compress
From
On 29/06/2023 22:29, Abhinav Kumar wrote:
> Instead of using a feature bit to decide whether to enable data
> compress or not for DSC use-cases, use dpu core's major version instead.
> This will avoid defining feature bits for every bit level details of
> registers.
>
> Also, rename the intf's enable_compression() op to program_datapath()
> and allow it to accept a struct intf_dpu_datapath_cfg to program
> all the bits at once. This can be re-used by widebus later on as
> well as it touches the same register.

Two separate commits please, because...

> Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
> ---
> .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 9 +++++++--
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++----
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h | 16 ++++++++++++++--
> 3 files changed, 26 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> index b856c6286c85..f4e15b4c4cc9 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> @@ -50,6 +50,7 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
> to_dpu_encoder_phys_cmd(phys_enc);
> struct dpu_hw_ctl *ctl;
> struct dpu_hw_intf_cfg intf_cfg = { 0 };
> + struct dpu_kms *dpu_kms = phys_enc->dpu_kms;
>
> ctl = phys_enc->hw_ctl;
> if (!ctl->ops.setup_intf_cfg)
> @@ -68,8 +69,12 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
> phys_enc->hw_intf,
> phys_enc->hw_pp->idx);
>
> - if (intf_cfg.dsc != 0 && phys_enc->hw_intf->ops.enable_compression)
> - phys_enc->hw_intf->ops.enable_compression(phys_enc->hw_intf);
> + if (intf_cfg.dsc != 0 && dpu_kms->catalog->core_major_version >= 0x7) {

... because this becomes incorrect. The datapath should be programmed in
all the cases, if there is a corresponding callback. intf_cfg.dsc should
be used as a condition to set datapath_cfg.


> + struct intf_dpu_datapath_cfg datapath_cfg = { 0 };

No need for `0' in the init, empty braces would be enough.

> +
> + datapath_cfg.data_compress = true;
> + phys_enc->hw_intf->ops.program_datapath(phys_enc->hw_intf, &datapath_cfg);
> + }
> }
>
> static void dpu_encoder_phys_cmd_pp_tx_done_irq(void *arg, int irq_idx)
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 5b0f6627e29b..85333df08fbc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -513,11 +513,13 @@ static void dpu_hw_intf_disable_autorefresh(struct dpu_hw_intf *intf,
>
> }
>
> -static void dpu_hw_intf_enable_compression(struct dpu_hw_intf *ctx)
> +static void dpu_hw_intf_program_datapath(struct dpu_hw_intf *ctx,
> + struct intf_dpu_datapath_cfg *datapath_cfg)
> {
> u32 intf_cfg2 = DPU_REG_READ(&ctx->hw, INTF_CONFIG2);
>
> - intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
> + if (datapath_cfg->data_compress)
> + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
>
> DPU_REG_WRITE(&ctx->hw, INTF_CONFIG2, intf_cfg2);
> }
> @@ -543,8 +545,7 @@ static void _setup_intf_ops(struct dpu_hw_intf_ops *ops,
> ops->disable_autorefresh = dpu_hw_intf_disable_autorefresh;
> }
>
> - if (cap & BIT(DPU_INTF_DATA_COMPRESS))
> - ops->enable_compression = dpu_hw_intf_enable_compression;
> + ops->program_datapath = dpu_hw_intf_program_datapath;

The `core_major_version >= 7' should either be here or in the callback
itself.

> }
>
> struct dpu_hw_intf *dpu_hw_intf_init(const struct dpu_intf_cfg *cfg,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> index 99e21c4137f9..f736dca38463 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> @@ -48,6 +48,11 @@ struct intf_status {
> u32 line_count; /* current line count including blanking */
> };
>
> +struct intf_dpu_datapath_cfg {
> + u8 data_compress; /* enable data compress between dpu and dsi */
> + /* can be expanded for other programmable bits */
> +};

I'd say, dpu_datapath is too generic. What about intf_cmd_mode_cfg?

> +
> /**
> * struct dpu_hw_intf_ops : Interface to the interface Hw driver functions
> * Assumption is these functions will be called after clocks are enabled
> @@ -70,7 +75,7 @@ struct intf_status {
> * @get_autorefresh: Retrieve autorefresh config from hardware
> * Return: 0 on success, -ETIMEDOUT on timeout
> * @vsync_sel: Select vsync signal for tear-effect configuration
> - * @enable_compression: Enable data compression
> + * @program_datapath: Program the DPU to interface datapath for relevant chipsets
> */
> struct dpu_hw_intf_ops {
> void (*setup_timing_gen)(struct dpu_hw_intf *intf,
> @@ -108,7 +113,14 @@ struct dpu_hw_intf_ops {
> */
> void (*disable_autorefresh)(struct dpu_hw_intf *intf, uint32_t encoder_id, u16 vdisplay);
>
> - void (*enable_compression)(struct dpu_hw_intf *intf);
> + /**
> + * Program the DPU to intf datapath by specifying
> + * which of the settings need to be programmed for
> + * use-cases which need DPU-intf handshake such as
> + * widebus, compression etc.

This is not a valid kerneldoc.

> + */
> + void (*program_datapath)(struct dpu_hw_intf *intf,
> + struct intf_dpu_datapath_cfg *datapath_cfg);
> };
>
> struct dpu_hw_intf {

--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2023-06-30 02:21    [W:0.057 / U:0.708 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site