lkml.org 
[lkml]   [2023]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 2/3] gpio: pcie-idio-24: Migrate to the regmap API
On Sun, Mar 26, 2023 at 12:25:58PM -0400, William Breathitt Gray wrote:
> The regmap API supports IO port accessors so we can take advantage of
> regmap abstractions rather than handling access to the device registers
> directly in the driver.
>
> For the PCIe-IDIO-24 series of devices, the following BARs are
> available:
>
> BAR[0]: memory mapped PEX8311
> BAR[1]: I/O mapped PEX8311
> BAR[2]: I/O mapped card registers
>
> There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
> lines (which may be configured for either output or input). The GPIO
> lines are exposed by the following card registers:
>
> Base +0x0-0x2 (Read/Write): FET Outputs
> Base +0xB (Read/Write): TTL/CMOS
> Base +0x4-0x6 (Read): Isolated Inputs
> Base +0x7 (Read): TTL/CMOS
>
> In order for the device to support interrupts, the PLX PEX8311 internal
> PCI wire interrupt and local interrupt input must first be enabled.
>
> The following card registers for Change-Of-State may be used:
>
> Base +0x8-0xA (Read): COS Status Inputs
> Base +0x8-0xA (Write): COS Clear Inputs
> Base +0xB (Read): COS Status TTL/CMOS
> Base +0xB (Write): COS Clear TTL/CMOS
> Base +0xE (Read/Write): COS Enable
>
> The COS Enable register is used to enable/disable interrupts and
> configure the interrupt levels; each bit maps to a group of eight inputs
> as described below:
>
> Bit 0: IRQ EN Rising Edge IN0-7
> Bit 1: IRQ EN Rising Edge IN8-15
> Bit 2: IRQ EN Rising Edge IN16-23
> Bit 3: IRQ EN Rising Edge TTL0-7
> Bit 4: IRQ EN Falling Edge IN0-7
> Bit 5: IRQ EN Falling Edge IN8-15
> Bit 6: IRQ EN Falling Edge IN16-23
> Bit 7: IRQ EN Falling Edge TTL0-7
>
> An interrupt is asserted when a change-of-state matching the interrupt
> level configuration respective for a particular group of eight inputs
> with enabled COS is detected.
>
> The COS Status registers may be read to determine which inputs have
> changed; if interrupts were enabled, an IRQ will be generated for the
> set bits in these registers. Writing the value read from the COS Status
> register back to the respective COS Clear register will clear just those
> interrupts.

...

> Cc: Arnaud de Turckheim <quarium@gmail.com>
> Cc: John Hentges <jhentges@accesio.com>
> Cc: Jay Dolan <jay.dolan@accesio.com>

You can use --cc parameter to the `git format-patch`.

...

> +static const struct regmap_config pex8311_intcsr_regmap_config = {
> + .name = "pex8311_intcsr",
> + .reg_bits = 32,
> + .reg_stride = 1,
> + .reg_base = PLX_PEX8311_PCI_LCS_INTCSR,
> + .val_bits = 32,
> + .io_port = true,
> + .max_register = 0x0,
> +};

Do you need regmap lock? If so, what for?

...

> +static const struct regmap_config idio_24_regmap_config = {
> + .reg_bits = 8,
> + .reg_stride = 1,
> + .val_bits = 8,
> + .io_port = true,
> + .max_register = 0xF,
> + .wr_table = &idio_24_wr_table,
> + .rd_table = &idio_24_rd_table,
> + .volatile_table = &idio_24_volatile_table,
> + .cache_type = REGCACHE_FLAT,
> +};

Ditto.

...

> +static int idio_24_set_type_config(unsigned int **const buf, const unsigned int type,
> + const struct regmap_irq *const irq_data, const int idx,
> + void *const irq_drv_data)
> {
> + const unsigned int offset = irq_data->reg_offset;
> + const unsigned int rising = COS_ENABLE_RISING << offset;
> + const unsigned int falling = COS_ENABLE_FALLING << offset;
> + const unsigned int mask = COS_ENABLE_BOTH << offset;
> + struct idio_24_gpio *const idio24gpio = irq_drv_data;
> + unsigned int new;
> + unsigned int cos_enable;
> + int ret;
> +
> + switch (type) {
> + case IRQ_TYPE_EDGE_RISING:
> + new = rising;
> + break;
> + case IRQ_TYPE_EDGE_FALLING:
> + new = falling;
> + break;
> + case IRQ_TYPE_EDGE_BOTH:
> + new = mask;
> + break;
> + default:
> + return -EINVAL;
> }
>
> + raw_spin_lock(&idio24gpio->lock);
>
> + /* replace old bitmap with new bitmap */
> + idio24gpio->irq_type = (idio24gpio->irq_type & ~mask) | (new & mask);
>
> + ret = regmap_read(idio24gpio->map, IDIO_24_COS_ENABLE, &cos_enable);
> + if (ret)
> + goto exit_early;
>
> + /* if COS is currently enabled then update the edge type */
> + if (cos_enable & mask) {
> + ret = regmap_update_bits(idio24gpio->map, IDIO_24_COS_ENABLE, mask,
> + idio24gpio->irq_type);
> + goto exit_early;
> }

> +exit_early:

More descriptive is to call it

exit_unlock:

The rule of thumb is to explain what _will_ happen, if we goto $LABEL.

> + raw_spin_unlock(&idio24gpio->lock);
>
> + return ret;
> }

--
With Best Regards,
Andy Shevchenko


\
 
 \ /
  Last update: 2023-03-27 13:00    [W:0.090 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site