lkml.org 
[lkml]   [2023]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] arm64: dts: qcom: sdm630: move DSI opp-table out of soc node
Date
The soc node is supposed to have only device nodes with MMIO addresses,
so move the DSI OPP out of it (it is used also by second DSI1 on
SDM660):

sda660-inforce-ifc6560.dtb: soc: opp-table-dsi: {'compatible': ['operating-points-v2'], ... should not be valid under {'type': 'object'}
From schema: dtschema/schemas/simple-bus.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

Changes since v1:
1. Move the node out of soc. Don't add Konrad's review tag.
---
arch/arm64/boot/dts/qcom/sdm630.dtsi | 38 ++++++++++++++--------------
1 file changed, 19 insertions(+), 19 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
index 72d9a12b5e9c..b91e423a3cfc 100644
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -328,6 +328,25 @@ memory@80000000 {
reg = <0x0 0x80000000 0x0 0x0>;
};

+ dsi_opp_table: opp-table-dsi {
+ compatible = "operating-points-v2";
+
+ opp-131250000 {
+ opp-hz = /bits/ 64 <131250000>;
+ required-opps = <&rpmpd_opp_svs>;
+ };
+
+ opp-210000000 {
+ opp-hz = /bits/ 64 <210000000>;
+ required-opps = <&rpmpd_opp_svs_plus>;
+ };
+
+ opp-262500000 {
+ opp-hz = /bits/ 64 <262500000>;
+ required-opps = <&rpmpd_opp_nom>;
+ };
+ };
+
pmu {
compatible = "arm,armv8-pmuv3";
interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
@@ -1450,25 +1469,6 @@ mmcc: clock-controller@c8c0000 {
<0>;
};

- dsi_opp_table: opp-table-dsi {
- compatible = "operating-points-v2";
-
- opp-131250000 {
- opp-hz = /bits/ 64 <131250000>;
- required-opps = <&rpmpd_opp_svs>;
- };
-
- opp-210000000 {
- opp-hz = /bits/ 64 <210000000>;
- required-opps = <&rpmpd_opp_svs_plus>;
- };
-
- opp-262500000 {
- opp-hz = /bits/ 64 <262500000>;
- required-opps = <&rpmpd_opp_nom>;
- };
- };
-
mdss: display-subsystem@c900000 {
compatible = "qcom,mdss";
reg = <0x0c900000 0x1000>,
--
2.34.1
\
 
 \ /
  Last update: 2023-03-27 01:17    [W:1.758 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site