lkml.org 
[lkml]   [2022]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net-next v2 01/35] dt-bindings: phy: Add QorIQ SerDes binding
From
Date
Hi Rob,

On 6/30/22 1:27 PM, Rob Herring wrote:
> On Tue, Jun 28, 2022 at 06:13:30PM -0400, Sean Anderson wrote:
>> This adds a binding for the SerDes module found on QorIQ processors. The
>> phy reference has two cells, one for the first lane and one for the
>> last. This should allow for good support of multi-lane protocols when
>> (if) they are added. There is no protocol option, because the driver is
>> designed to be able to completely reconfigure lanes at runtime.
>> Generally, the phy consumer can select the appropriate protocol using
>> set_mode. For the most part there is only one protocol controller
>> (consumer) per lane/protocol combination. The exception to this is the
>> B4860 processor, which has some lanes which can be connected to
>> multiple MACs. For that processor, I anticipate the easiest way to
>> resolve this will be to add an additional cell with a "protocol
>> controller instance" property.
>>
>> Each serdes has a unique set of supported protocols (and lanes). The
>> support matrix is stored in the driver and is selected based on the
>> compatible string. It is anticipated that a new compatible string will
>> need to be added for each serdes on each SoC that drivers support is
>> added for. There is no "generic" compatible string for this reason.
>>
>> There are two PLLs, each of which can be used as the master clock for
>> each lane. Each PLL has its own reference. For the moment they are
>> required, because it simplifies the driver implementation. Absent
>> reference clocks can be modeled by a fixed-clock with a rate of 0.
>>
>> Signed-off-by: Sean Anderson <sean.anderson@seco.com>
>> ---
>>
>> Changes in v2:
>> - Add #clock-cells. This will allow using assigned-clocks* to configure
>> the PLLs.
>> - Allow a value of 1 for phy-cells. This allows for compatibility with
>> the similar (but according to Ioana Ciornei different enough) lynx-28g
>> binding.
>> - Document phy cells in the description
>> - Document the structure of the compatible strings
>> - Fix example binding having too many cells in regs
>> - Move compatible first
>> - Refer to the device in the documentation, rather than the binding
>> - Remove minItems
>> - Rename to fsl,lynx-10g.yaml
>> - Use list for clock-names
>>
>> .../devicetree/bindings/phy/fsl,lynx-10g.yaml | 93 +++++++++++++++++++
>> 1 file changed, 93 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml b/Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
>> new file mode 100644
>> index 000000000000..b5a6f631df9f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
>> @@ -0,0 +1,93 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/phy/fsl,lynx-10g.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: NXP Lynx 10G SerDes
>> +
>> +maintainers:
>> + - Sean Anderson <sean.anderson@seco.com>
>> +
>> +description: |
>> + These Lynx "SerDes" devices are found in NXP's QorIQ line of processors. The
>> + SerDes provides up to eight lanes. Each lane may be configured individually,
>> + or may be combined with adjacent lanes for a multi-lane protocol. The SerDes
>> + supports a variety of protocols, including up to 10G Ethernet, PCIe, SATA, and
>> + others. The specific protocols supported for each lane depend on the
>> + particular SoC.
>> +
>> +properties:
>> + compatible:
>> + description: |
>> + Each compatible is of the form "fsl,<soc-name>-serdes-<instance>".
>> + Although many registers are compatible between different SoCs, the
>> + supported protocols and lane assignments tend to be unique to each SerDes.
>> + Additionally, the method of activating protocols may also be unique.
>
> We typically have properties for handling these variables. Numbering
> instances is something we avoid.

On v1, Krzysztof said that this was a better route...

>> + Because of this, each SerDes instance will need its own compatible string.
>
>> + In cases where two SoCs share the same SerDes implementation (such as the
>> + LS1046A and LS1026A), both SoCs should share the same compatible strings.
>
> No, not unless the 2 parts are just fuse or package pinout differences.
> Otherwise, there's always the chance they are not 'the same' and have
> different bugs.
>
> You could have "fsl,ls1046a-serdes", "fsl,ls1026a-serdes" (whichever SoC
> is older last) if you think they are 'the same'.

Fine by me.

>> + enum:
>> + - fsl,ls1046a-serdes-1
>> + - fsl,ls1046a-serdes-2
>> +
>> + "#clock-cells":
>> + const: 1
>> + description: |
>> + The cell contains the index of the PLL, starting from 0. Note that when
>> + assigning a rate to a PLL, the PLLs' rates are divided by 1000 to avoid
>> + overflow. A rate of 5000000 corresponds to 5GHz.
>> +
>> + "#phy-cells":
>> + minimum: 1
>> + maximum: 2
>> + description: |
>> + The cells contain the following arguments:
>> + - The first lane in the group. Lanes are numbered based on the register
>> + offsets, not the I/O ports. This corresponds to the letter-based ("Lane
>> + A") naming scheme, and not the number-based ("Lane 0") naming scheme. On
>> + most SoCs, "Lane A" is "Lane 0", but not always.
>> + - Last lane. For single-lane protocols, this should be the same as the
>> + first lane.
>> + If no lanes in a SerDes can be grouped, then #phy-cells may be 1, and the
>> + first cell will specify the only lane in the group.
>
> Usually when we have per lane phys, the consumer side will have a 'phys'
> entry per lane.

The problem is that it is hard to coordinate multiple lanes coming up at once. There
are particular ordering requirements when multiple lanes are grouped together:

> Note that if the lanes being reconfigured are grouped for multi-lane or synchronous
> mode, then the master source clock lane for the group must have TRST_B set to 1
> after all the other lanes in the group. The master source clock lane of the group
> is indicated by LNmGCR0[1STLANE]=1. All lanes p<m (if LNmGCR1[TRSTDIR]=0) or p> (if LNmGCR1[TRSTDIR]=1) of the master source clock lane until the next lane with
> LNmGCR0[1STLANE]=1, or the end of the SerDes, are grouped with the master source
> clock lane. All grouped lanes must have the same setting of TRSTDIR.

This is trivial to do if we enable things as a "group" but not so easy if each lane
is a separate phy. In particular, we have to know up front whether lanes are being
grouped together in order to program 1STLANE correctly. I think the enable order
corresponds to the order in the dtb, but AFAIK that is not guaranteed by the phy
subsystem.

> Having a variable number of cells isn't great either. We usually only do
> that when we have to extend an existing binding.

This is mainly to align closer to the lynx-28g binding. It can always be restricted.

>> +
>> + clocks:
>> + maxItems: 2
>> + description: |
>> + Clock for each PLL reference clock input.
>> +
>> + clock-names:
>> + items:
>> + - enum: &clocks
>> + - ref0
>> + - ref1
>> + - enum: *clocks
>
> Whoa, there's a first. Don't use YAML anchors and references. We only
> support JSON subset of YAML.

How else should this be expressed? I would like to allow both

clock-names = "ref0", "ref1";

and

clock-names = "ref1", "ref0";

ideally without repeating myself.

--Sean

>> +
>> + reg:
>> + maxItems: 1
>> +
>> +required:
>> + - "#clock-cells"
>> + - "#phy-cells"
>> + - compatible
>> + - clocks
>> + - clock-names
>> + - reg
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + serdes1: phy@1ea0000 {
>> + #clock-cells = <1>;
>> + #phy-cells = <2>;
>> + compatible = "fsl,ls1046a-serdes-1";
>> + reg = <0x1ea0000 0x2000>;
>> + clocks = <&clk_100mhz>, <&clk_156mhz>;
>> + clock-names = "ref0", "ref1";
>> + assigned-clocks = <&serdes1 0>;
>> + assigned-clock-rates = <5000000>;
>> + };
>> +
>> +...
>> --
>> 2.35.1.1320.gc452695387.dirty
>>
>>
>

\
 
 \ /
  Last update: 2022-06-30 20:02    [W:0.136 / U:1.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site