lkml.org 
[lkml]   [2022]   [Apr]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: dts: BCM5301X: Add DT for Buffalo WZR-1166DHP2
Date
Buffalo WZR-1166DHP2  wireless router with

- BCM4708A0
- 256MiB DDR2 SDRAM
- 128MiB NAND flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 4x 10/100M ethernet switch

The hardware configuration is very similar to the WZR-1750DHP,
except for memory size and number of antennas.

Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
---
.../boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts | 189 ++++++++++++++++++
1 file changed, 189 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts

diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 000000000000..22e54a0a202a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+ compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+ model = "Buffalo WZR-1166DHP2 (BCM4708)";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>,
+ <0x88000000 0x08000000>;
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ num-chipselects = <1>;
+ gpio-sck = <&chipcommon 7 0>;
+ gpio-mosi = <&chipcommon 4 0>;
+ cs-gpios = <&chipcommon 6 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hc595: gpio_spi@0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ registers-number = <1>;
+ spi-max-frequency = <100000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ usb {
+ label = "bcm53xx:blue:usb";
+ gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+ trigger-sources = <&ohci_port1>, <&ehci_port1>,
+ <&xhci_port1>, <&ohci_port2>,
+ <&ehci_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ power0 {
+ label = "bcm53xx:red:power";
+ gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ power1 {
+ label = "bcm53xx:white:power";
+ gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ router0 {
+ label = "bcm53xx:blue:router";
+ gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ router1 {
+ label = "bcm53xx:amber:router";
+ gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan {
+ label = "bcm53xx:blue:wan";
+ gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ wireless0 {
+ label = "bcm53xx:blue:wireless";
+ gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ wireless1 {
+ label = "bcm53xx:amber:wireless";
+ gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+ };
+
+ aoss {
+ label = "AOSS";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Commit mode set by switch? */
+ mode {
+ label = "Mode";
+ linux,code = <KEY_SETUP>;
+ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Switch: AP mode */
+ sw_ap {
+ label = "AP";
+ linux,code = <BTN_0>;
+ gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+ };
+
+ eject {
+ label = "USB eject";
+ linux,code = <KEY_EJECTCD>;
+ gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&usb2 {
+ vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+ vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+ status = "okay";
+};
+
+&usb3_phy {
+ status = "okay";
+};
+
+&srab {
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ };
+ };
+};
--
2.30.2
\
 
 \ /
  Last update: 2022-04-12 17:46    [W:0.044 / U:0.444 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site