lkml.org 
[lkml]   [2022]   [Mar]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] brcmfmac: Avoid keeping power to SDIO card unless WOWL is used
Date
Keeping the power to the SDIO card during system wide suspend, consumes
energy. Especially on battery driven embedded systems, this can be a
problem. Therefore, let's change the behaviour into allowing the SDIO card
to be powered off, unless WOWL is supported and enabled.

Note that, the downside from this change, is that at system resume the SDIO
card needs to be re-initialized and the FW must re-programmed. Even it that
may take some time to complete, it should we worth it, rather than draining
a battery.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---

Please note that, I have only compile-tested this patch, so I am relying on help
from Yann and others to run tests on real HW.

Kind regards
Ulf Hansson

---
.../broadcom/brcm80211/brcmfmac/bcmsdh.c | 33 +++++++++++--------
1 file changed, 20 insertions(+), 13 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
index ac02244a6fdf..351886c9d68e 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
@@ -1119,9 +1119,21 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
{
struct brcmf_bus *bus_if = dev_get_drvdata(dev);
struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;
+ mmc_pm_flag_t pm_caps = sdio_get_host_pm_caps(sdiodev->func1);

- brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
- sdiodev->wowl_enabled = enabled;
+ /* Power must be preserved to be able to support WOWL. */
+ if (!(pm_caps & MMC_PM_KEEP_POWER))
+ goto notsup;
+
+ if (sdiodev->settings->bus.sdio.oob_irq_supported ||
+ pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
+ sdiodev->wowl_enabled = enabled;
+ brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
+ return;
+ }
+
+notsup:
+ brcmf_dbg(SDIO, "WOWL not supported\n");
}

#ifdef CONFIG_PM_SLEEP
@@ -1130,7 +1142,7 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
struct sdio_func *func;
struct brcmf_bus *bus_if;
struct brcmf_sdio_dev *sdiodev;
- mmc_pm_flag_t pm_caps, sdio_flags;
+ mmc_pm_flag_t sdio_flags;
int ret = 0;

func = container_of(dev, struct sdio_func, dev);
@@ -1142,20 +1154,15 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
bus_if = dev_get_drvdata(dev);
sdiodev = bus_if->bus_priv.sdio;

- pm_caps = sdio_get_host_pm_caps(func);
-
- if (pm_caps & MMC_PM_KEEP_POWER) {
- /* preserve card power during suspend */
+ if (sdiodev->wowl_enabled) {
brcmf_sdiod_freezer_on(sdiodev);
brcmf_sdio_wd_timer(sdiodev->bus, 0);

sdio_flags = MMC_PM_KEEP_POWER;
- if (sdiodev->wowl_enabled) {
- if (sdiodev->settings->bus.sdio.oob_irq_supported)
- enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
- else
- sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
- }
+ if (sdiodev->settings->bus.sdio.oob_irq_supported)
+ enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
+ else
+ sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;

if (sdio_set_host_pm_flags(sdiodev->func1, sdio_flags))
brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
--
2.25.1
\
 
 \ /
  Last update: 2022-03-17 16:30    [W:0.059 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site