lkml.org 
[lkml]   [2022]   [Mar]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] mmc: core: Set HS clock speed before sending HS CMD13
Date
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands

It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.

Anyway, the aforementioned commit got that right for HS400ES, but the
refactoring in 53e60650f74e ("mmc: core: Allow CMD13 polling when
switching to HS mode for mmc") messed that back up again, by reordering
step 2 after step 3.

Let's fix that, and also apply the same logic to HS200/400, where this
eMMC has problems too.

This resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:

[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card

Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
---

drivers/mmc/core/mmc.c | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 13abfcd130a5..821b90caba2f 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -1390,12 +1390,17 @@ static int mmc_select_hs400es(struct mmc_card *card)
}

mmc_set_timing(host, MMC_TIMING_MMC_HS);
+
+ /*
+ * Bump to HS frequency. Some cards don't handle SEND_STATUS reliably
+ * at the initial frequency.
+ */
+ mmc_set_clock(host, card->ext_csd.hs_max_dtr);
+
err = mmc_switch_status(card, true);
if (err)
goto out_err;

- mmc_set_clock(host, card->ext_csd.hs_max_dtr);
-
/* Switch card to DDR with strobe bit */
val = EXT_CSD_DDR_BUS_WIDTH_8 | EXT_CSD_BUS_WIDTH_STROBE;
err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
@@ -1487,6 +1492,12 @@ static int mmc_select_hs200(struct mmc_card *card)
old_timing = host->ios.timing;
mmc_set_timing(host, MMC_TIMING_MMC_HS200);

+ /*
+ * Bump to HS frequency. Some cards don't handle SEND_STATUS
+ * reliably at the initial frequency.
+ */
+ mmc_set_clock(host, card->ext_csd.hs_max_dtr);
+
/*
* For HS200, CRC errors are not a reliable way to know the
* switch failed. If there really is a problem, we would expect
--
2.35.1.723.g4982287a31-goog
\
 
 \ /
  Last update: 2022-03-10 21:58    [W:0.076 / U:1.968 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site