lkml.org 
[lkml]   [2022]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] arm64: dts: qcom: sm6115: Move SDHC node(s)'s 'pinctrl' properties to dts
Date
Normally the 'pinctrl' properties of a SDHC controller and the
chip detect pin settings are dependent on the type of the slots
(for e.g uSD card slot), regulators and GPIO(s) available on the
board(s).

So, move the same from the sm6115 dtsi file to the respective
board file(s).

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
.../boot/dts/qcom/sm4250-oneplus-billie2.dts | 10 +++++++++
arch/arm64/boot/dts/qcom/sm6115.dtsi | 22 -------------------
2 files changed, 10 insertions(+), 22 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
index a3f1c7c41fd73..329eb496bbc5f 100644
--- a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
+++ b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
@@ -202,12 +202,22 @@ &sdhc_2 {
vqmmc-supply = <&vreg_l5a>;

cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_state_on &sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_state_off &sdc2_card_det_n>;

status = "okay";
};

&tlmm {
gpio-reserved-ranges = <14 4>;
+
+ sdc2_card_det_n: sd-card-det-n-state {
+ pins = "gpio88";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
};

&ufs_mem_hc {
diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
index 572bf04adf906..6be763d39870d 100644
--- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
@@ -518,13 +518,6 @@ data-pins {
bias-pull-up;
drive-strength = <10>;
};
-
- sd-cd-pins {
- pins = "gpio88";
- function = "gpio";
- bias-pull-up;
- drive-strength = <2>;
- };
};

sdc2_state_off: sdc2-off-state {
@@ -545,13 +538,6 @@ data-pins {
bias-pull-up;
drive-strength = <2>;
};
-
- sd-cd-pins {
- pins = "gpio88";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- };
};
};

@@ -652,10 +638,6 @@ sdhc_1: mmc@4744000 {
<&gcc GCC_SDCC1_ICE_CORE_CLK>;
clock-names = "iface", "core", "xo", "ice";

- pinctrl-0 = <&sdc1_state_on>;
- pinctrl-1 = <&sdc1_state_off>;
- pinctrl-names = "default", "sleep";
-
bus-width = <8>;
status = "disabled";
};
@@ -672,10 +654,6 @@ sdhc_2: mmc@4784000 {
clocks = <&gcc GCC_SDCC2_AHB_CLK>, <&gcc GCC_SDCC2_APPS_CLK>, <&xo_board>;
clock-names = "iface", "core", "xo";

- pinctrl-0 = <&sdc2_state_on>;
- pinctrl-1 = <&sdc2_state_off>;
- pinctrl-names = "default", "sleep";
-
power-domains = <&rpmpd SM6115_VDDCX>;
operating-points-v2 = <&sdhc2_opp_table>;
iommus = <&apps_smmu 0x00a0 0x0>;
--
2.38.1
\
 
 \ /
  Last update: 2023-03-26 23:15    [W:0.057 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site