lkml.org 
[lkml]   [2022]   [Nov]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes
On Wed, Nov 16, 2022 at 03:22:11PM +0200, Abel Vesa wrote:
> Add USB host controller and PHY nodes.
>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8550.dtsi | 99 ++++++++++++++++++++++++++++
> 1 file changed, 99 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 07ba709ca35f..1b62395fe101 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -1460,6 +1460,105 @@ opp-202000000 {
> };
> };
>
> + usb_1_hsphy: phy@88e3000 {
> + compatible = "qcom,sm8550-snps-eusb2-phy";
> + reg = <0x0 0x088e3000 0x0 0x154>;
> + status = "disabled";
> + #phy-cells = <0>;
> +
> + clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
> + clock-names = "ref";
> +
> + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> + };
> +
> + usb_1_qmpphy: phy-wrapper@88e9000 {
> + compatible = "qcom,sm8550-qmp-usb3-phy";

Where's the corresponding binding update?

> + reg = <0x0 0x088e9000 0x0 0x200>,
> + <0x0 0x088e8000 0x0 0x20>;
> + status = "disabled";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + <&rpmhcc RPMH_CXO_PAD_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "ref_clk_src", "com_aux";

Don't you have a dedicated ref clk? In any case, ref_clk_src should not
be here (either rename it 'ref' or replace it).

> +
> + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
> + <&gcc GCC_USB3_PHY_PRIM_BCR>;
> + reset-names = "phy", "common";
> + power-domains = <&gcc USB3_PHY_GDSC>;
> +
> + usb_1_ssphy: phy@88e9200 {
> + reg = <0x0 0x088e9200 0x0 0x200>,
> + <0x0 0x088e9400 0x0 0x200>,
> + <0x0 0x088e9c00 0x0 0x400>,
> + <0x0 0x088e9600 0x0 0x200>,
> + <0x0 0x088e9800 0x0 0x200>,
> + <0x0 0x088e9a00 0x0 0x100>;
> + #phy-cells = <0>;
> + #clock-cells = <0>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_phy_pipe_clk_src";
> + };

As for UFS and PCIe these PHY nodes should be updated to use the new
binding scheme which drops the child node and individual register
descriptions (cf. sc8280xp).

> + };

Johan

\
 
 \ /
  Last update: 2022-11-16 14:44    [W:0.065 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site