lkml.org 
[lkml]   [2022]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v10 1/2] dt-bindings: mfd: Add MAX5970 and MAX5978
From
Hi Krzysztof,

On 15-11-2022 07:34 pm, Krzysztof Kozlowski wrote:
> On 15/11/2022 12:09, Naresh Solanki wrote:
>> From: Marcello Sylvester Bauer <sylv@sylv.io>
>>
>> The MAX597x is a hot swap controller with configurable fault protection.
>> It also has 10bit ADC for current & voltage measurements.
>>
>> Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
>> Co-developed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
>> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
>> Co-developed-by: Naresh Solanki <Naresh.Solanki@9elements.com>
>> Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
>> ---
>> .../bindings/mfd/maxim,max5970.yaml | 154 ++++++++++++++++++
>> 1 file changed, 154 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max5970.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml b/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml
>> new file mode 100644
>> index 000000000000..edf0c23db4ca
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml
>> @@ -0,0 +1,154 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mfd/maxim,max5970.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Regulator for MAX5970 smart switch from Maxim Integrated.
>> +
>> +maintainers:
>> + - Patrick Rudolph <patrick.rudolph@9elements.com>
>> +
>> +description: |
>> + The smart switch provides no output regulation, but independent fault protection
>> + and voltage and current sensing.
>> + Programming is done through I2C bus.
>> +
>> + Datasheets:
>> + https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf
>> + https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - maxim,max5970
>> + - maxim,max5978
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + leds:
>> + type: object
>> + description:
>> + Properties for four LEDS.
>> +
>> + properties:
>> + "#address-cells":
>> + const: 1
>> +
>> + "#size-cells":
>> + const: 0
>> +
>> + patternProperties:
>> + "^led@[0-3]$":
>> + $ref: /schemas/leds/common.yaml#
>> + type: object
>> +
>> + additionalProperties: false
>> +
>> + vss1-supply:
>> + description: Supply of the first channel.
>> +
>> + vss2-supply:
>> + description: Supply of the second channel.
>> +
>> + regulators:
>> + type: object
>> + description:
>> + Properties for both regulators. Also set value for shunt resistor used.
>
> You should explain not the syntax, but what part of hardware this nodes
> represents. Therefore "Also set value" does not fit at all. Hardware
> sets value?
You mean something like: Properties for power switch
>
> I looked at datasheets to figure it out but they do not refer to any
> configurable regulator, LDO nor "sw0/sw1/sw2". Therefore I have no clue
> what to expect here...
Yes this is for power switch part of max5970/8
>
>> +
>> + patternProperties:
>> + "^sw[0-1]$":
>> + $ref: /schemas/regulator/regulator.yaml#
>> + type: object
>> + properties:
>> + shunt-resistor-micro-ohms:
>> + description: |
>> + The value of current sense resistor in microohms.
>> +
>> + required:
>> + - shunt-resistor-micro-ohms
>> +
>> + unevaluatedProperties: false
>
> I don't think it has proper indentation. Did you test the binding?
Definitely tested the bindings before I push the patch.
>
>> +
>> + additionalProperties: false
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - regulators
>> + - vss1-supply
>> +
>> +allOf:
>> + - if:
>> + properties:
>> + compatible:
>> + enum:
>> + - maxim,max5970
>> + then:
>> + required:
>> + - vss2-supply
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + i2c {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + regulator@3a {
>> + compatible = "maxim,max5978";
>> + reg = <0x3a>;
>> + vss1-supply = <&p3v3>;
>> +
>> + regulators {
>> + sw0_ref_0: sw0 {
>> + regulator-compatible = "SW0";
>> + shunt-resistor-micro-ohms = <12000>;
>> + };
>> + };
>> +
>> + leds {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + led@0 {
>> + reg = <0>;
>> + label = "led0";
>> + default-state = "on";
>> + };
>> + led@1 {
>> + reg = <1>;
>> + label = "led1";
>> + default-state = "on";
>> + };
>> + };
>> + };
>> + };
>> +
>> + - |
>> + i2c {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + regulator@3a {
>> + compatible = "maxim,max5970";
>> + reg = <0x3a>;
>> + vss1-supply = <&p3v3>;
>> + vss2-supply = <&p5v>;
>> +
>> + regulators {
>> + sw0_ref_1: sw0 {
>> + regulator-compatible = "SW0";
>
> This property is deprecated, isn't it? Again - did you test this?
Yes tested.
>
> Best regards,
> Krzysztof
>

Regards,
Naresh

\
 
 \ /
  Last update: 2022-11-15 21:34    [W:0.504 / U:0.688 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site