lkml.org 
[lkml]   [2022]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] dt-bindings: iio: magnetometer: add ti tmag5273 documentation file
On Tue, 15 Nov 2022 08:37:17 +0100
Gerald Loacker <gerald.loacker@wolfvision.net> wrote:

> Add bindings documentation file for TI TMAG5273.
>
> Signed-off-by: Gerald Loacker <gerald.loacker@wolfvision.net>
> ---
> .../iio/magnetometer/ti,tmag5273.yaml | 72 +++++++++++++++++++
> MAINTAINERS | 6 ++
> 2 files changed, 78 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/magnetometer/ti,tmag5273.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ti,tmag5273.yaml b/Documentation/devicetree/bindings/iio/magnetometer/ti,tmag5273.yaml
> new file mode 100644
> index 000000000000..2f5b0a4d2f40
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/magnetometer/ti,tmag5273.yaml
> @@ -0,0 +1,72 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/magnetometer/ti,tmag5273.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TI TMAG5273 Low-Power Linear 3D Hall-Effect Sensor
> +
> +maintainers:
> + - Gerald Loacker <gerald.loacker@wolfvision.net>
> +
> +description:
> + The TI TMAG5273 is a low-power linear 3D Hall-effect sensor. This device
> + integrates three independent Hall-effect sensors in the X, Y, and Z axes.
> + The device has an integrated temperature sensor available. The TMAG5273
> + can be configured through the I2C interface to enable any combination of
> + magnetic axes and temperature measurements. An integrated angle calculation
> + engine (CORDIC) provides full 360° angular position information for both
> + on-axis and off-axis angle measurement topologies. The angle calculation is
> + performed using two user-selected magnetic axes.
> +
> +properties:
> + $nodename:
> + pattern: '^magnetometer@[0-9a-f]+$'

What Krzysztof said on this ;)

> +
> + compatible:
> + const: ti,tmag5273
> +
> + reg:
> + maxItems: 1
> +
> + "#io-channel-cells":
> + const: 1
> +
> + ti,angle-enable:
> + description:
> + Enables angle measurement in the selected plane.
> + 0 = OFF
> + 1 = X-Y (default)
> + 2 = Y-Z
> + 3 = X-Z

This feels like something we should be configuring at runtime rather that
DT, or is it driven by board design or similar?

> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0
> + maximum: 3
> +
> + vcc-supply:
> + description:
> + A regulator providing 1.7 V to 3.6 V supply voltage on the VCC pin,
> + typically 3.3 V.
> +

The dt binding should attempt to describe the hardware, not what we happen
to support in the driver so far. So I'd expect to also see an interrupt.
That way if someone ships a dts file today, and we enable it sometime in the
future they will be ready for it.

> +required:
> + - compatible
> + - reg
> + - vcc-supply

Ah. This is presumably as side effect of having the driver set the voltage.
Normally we only need to 'require' a supply if we need to read it's voltage
(for scaling on ADCs and similar). That's not the case here so I wouldn't
expect to see it.

> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + i2c-0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + magnetometer@35 {
> + compatible = "ti,tmag5273";
> + reg = <0x35>;
> + #io-channel-cells = <1>;
> + ti,angle-enable = <3>;
> + vcc-supply = <&vcc3v3>;
> + };
> + };
> +...


\
 
 \ /
  Last update: 2022-11-15 18:44    [W:0.081 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site