lkml.org 
[lkml]   [2022]   [Oct]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v10 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit
From
On 24/10/2022 13:42, Dzmitry Sankouski wrote:
> New device support - Xiaomi Mi6 phone
>
> What works:
> - storage
> - usb
> - power regulators
>
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---
> Changes for v2:
> - remove memory nodes before redefining
> - add board compatible to schema
> - remove board msm-id, add chassis type
> - remove common dtsi
> - move resin to pm8998 dtsi file
> - dts formatting
> - unsupported properties removed
> - add copyright
> - rebase on latest master(6.0.0-rc6)
> Changes for v3:
> - regulators nodes renamed to match pattern 'regulators-[01]'
> - duplicate cci1-default node deleted
> - add state suffix to '.*(active|suspend|default)' pinctrl
> - rebase on latest master(6.0.0)
> Changes for v4:
> - fix dts compilation errors(rename pinctrl label usages)
> Changes for v5:
> - use pm8005_regulators label
> Changes for v6:
> - add state suffix to all pinctrl
> - move status nodes to last position
> - disable resin node by default
> - move the debounce param to pm8998.dtsi file
> - place this patch after dt-binding patch
> Changes for v7:
> - fix Properties must precede subnodes dts compilation error
> Changes for v8:
> - enable resin node
> - rename nodes in reserved memory to comply with 'memory@.*' pattern
> Changes for v9: none
> Changes for v10:
> - reorder resin node content
> - reorder reserved memory nodes
> - increase reserved memory for adsp to comply with vendor kernel
> - new line in blsp1_uart3 node
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 710 ++++++++++++++++++
> arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 +
> 3 files changed, 719 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1d86a33de528..0460aabf1b59 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> new file mode 100644
> index 000000000000..ea66583fe74d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> @@ -0,0 +1,710 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
> + *
> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8998.dtsi"
> +#include "pm8005.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +
> +/*
> + * Delete following upstream (msm8998.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &adsp_mem;
> +/delete-node/ &mpss_mem;
> +/delete-node/ &venus_mem;
> +/delete-node/ &mba_mem;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &ipa_fw_mem;
> +/delete-node/ &ipa_gsi_mem;
> +/delete-node/ &gpu_mem;
> +/delete-node/ &wlan_msa_mem;
> +
> +/ {
> + model = "Xiaomi Mi 6";
> + compatible = "xiaomi,sagit", "qcom,msm8998";
> + chassis-type = "handset";
> + /* Required for bootloader to select correct board */
> + qcom,board-id = <30 0>;
> +
> + reserved-memory {
> + /*
> + * Xiaomi's ADSP firmware requires 30 MiB in total, so increase the adsp_mem
> + * region by 4 MiB to account for this while relocating the other now
> + * conflicting memory nodes accordingly.
> + */
> + adsp_mem: memory@8b200000 {
> + reg = <0x0 0x8b200000 0x0 0x1e00000>;
> + no-map;
> + };
> +
> + mpss_mem: memory@8d000000 {
> + reg = <0x0 0x8d000000 0x0 0x7000000>;
> + no-map;
> + };
> +
> + venus_mem: memory@94000000 {
> + reg = <0x0 0x94000000 0x0 0x500000>;
> + no-map;
> + };
> +
> + mba_mem: memory@94500000 {
> + reg = <0x0 0x94500000 0x0 0x200000>;
> + no-map;
> + };
> +
> + slpi_mem: memory@94700000 {
> + reg = <0x0 0x94700000 0x0 0xf00000>;
> + no-map;
> + };
> +
> + ipa_fw_mem: memory@95600000 {
> + reg = <0x0 0x95600000 0x0 0x10000>;
> + no-map;
> + };
> +
> + ipa_gsi_mem: memory@95610000 {
> + reg = <0x0 0x95610000 0x0 0x5000>;
> + no-map;
> + };
> +
> + gpu_mem: memory@95615000 {
> + reg = <0x0 0x95615000 0x0 0x100000>;
> + no-map;
> + };
> +
> + wlan_msa_mem: memory@95715000 {
> + reg = <0x0 0x95715000 0x0 0x100000>;
> + no-map;
> + };
> +
> + /* Bootloader display framebuffer region */
> + cont_splash_mem: memory@9d400000 {
> + reg = <0x0 0x9d400000 0x0 0x2400000>;
> + no-map;
> + };
> +
> + /* For getting crash logs using Android downstream kernels */
> + ramoops@ac000000 {
> + compatible = "ramoops";
> + reg = <0x0 0xac000000 0x0 0x200000>;
> + console-size = <0x80000>;
> + pmsg-size = <0x40000>;
> + record-size = <0x8000>;
> + ftrace-size = <0x20000>;
> + };
> +
> + /*
> + * The following memory regions on downstream are "dynamically allocated"
> + * but given the same addresses every time. Hard code them as these addresses
> + * are where the Xiaomi signed firmware expects them to be.
> + */
> + ipa_fws_region: memory@f7800000 {
> + compatible = "shared-dma-pool";
> + reg = <0x0 0xf7800000 0x0 0x5000>;
> + no-map;
> + };
> +
> + zap_shader_region: memory@f7900000 {
> + compatible = "shared-dma-pool";
> + reg = <0x0 0xf7900000 0x0 0x2000>;
> + no-map;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + label = "Volume buttons";
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vol_up_key_default>;
> +
> + key-vol-up {
> + label = "Volume up";
> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + debounce-interval = <15>;
> + wakeup-source;
> + };
> + };
> +
> + gpio-hall-sensor {
> + compatible = "gpio-keys";
> + label = "Hall effect sensor";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&hall_sensor_default_state>;
> +
> + event-hall-sensor {
> + label = "Hall Effect Sensor";
> + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
> + linux,input-type = <EV_SW>;
> + linux,code = <SW_LID>;
> + linux,can-disable;
> + wakeup-source;
> + };
> + };
> +
> + vph_pwr: vph-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + disp_vddts_vreg: disp-vddts-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "disp-vddts-regulator";
> + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + };
> +};
> +
> +&blsp1_i2c5 {
> + pinctrl-names = "default", "sleep";
> + status = "okay";
> +
> + touchscreen@20 {
> + compatible = "syna,rmi4-i2c";
> + reg = <0x20>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&ts_active_state>;
> + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
> +
> + vdd-supply = <&disp_vddts_vreg>;
> + vio-supply = <&vreg_l6a_1p8>;
> +
> + syna,reset-delay-ms = <20>;
> + syna,startup-delay-ms = <20>;
> +
> + rmi4-f01@1 {
> + reg = <0x01>;
> + syna,nosleep-mode = <1>;
> + };
> +
> + rmi4-f12@12 {
> + reg = <0x12>;
> + touchscreen-x-mm = <64>;
> + touchscreen-y-mm = <114>;
> + syna,sensor-type = <1>;
> + syna,rezero-wait-ms = <20>;
> + };
> +
> + rmi4-f1a@1a {
> + reg = <0x1a>;
> + syna,codes = <KEY_BACK KEY_APPSELECT>;
> + };
> + };
> +};
> +
> +&blsp1_i2c5_sleep {
> + /delete-property/ bias-pull-up;
> + bias-disable;
> +};
> +
> +&blsp1_uart3 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&blsp1_uart3_on {
> + rx {

You need to rebase your changes. This won't work.

If you test your DTS with dtbs_check, you will see the warnings.



Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-10-25 00:35    [W:0.068 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site