lkml.org 
[lkml]   [2022]   [Nov]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v10 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit
Hi, I rebased on 6.1-rc3, and found 1 issue related to sagit - missing
regulator in qusb2phy node.

пн, 24 окт. 2022 г. в 23:54, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org>:
>
> On 24/10/2022 13:42, Dzmitry Sankouski wrote:
> > New device support - Xiaomi Mi6 phone
> >
> > What works:
> > - storage
> > - usb
> > - power regulators
> >
> > Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> > ---
> > Changes for v2:
> > - remove memory nodes before redefining
> > - add board compatible to schema
> > - remove board msm-id, add chassis type
> > - remove common dtsi
> > - move resin to pm8998 dtsi file
> > - dts formatting
> > - unsupported properties removed
> > - add copyright
> > - rebase on latest master(6.0.0-rc6)
> > Changes for v3:
> > - regulators nodes renamed to match pattern 'regulators-[01]'
> > - duplicate cci1-default node deleted
> > - add state suffix to '.*(active|suspend|default)' pinctrl
> > - rebase on latest master(6.0.0)
> > Changes for v4:
> > - fix dts compilation errors(rename pinctrl label usages)
> > Changes for v5:
> > - use pm8005_regulators label
> > Changes for v6:
> > - add state suffix to all pinctrl
> > - move status nodes to last position
> > - disable resin node by default
> > - move the debounce param to pm8998.dtsi file
> > - place this patch after dt-binding patch
> > Changes for v7:
> > - fix Properties must precede subnodes dts compilation error
> > Changes for v8:
> > - enable resin node
> > - rename nodes in reserved memory to comply with 'memory@.*' pattern
> > Changes for v9: none
> > Changes for v10:
> > - reorder resin node content
> > - reorder reserved memory nodes
> > - increase reserved memory for adsp to comply with vendor kernel
> > - new line in blsp1_uart3 node
> >
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 710 ++++++++++++++++++
> > arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 +
> > 3 files changed, 719 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index 1d86a33de528..0460aabf1b59 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> > new file mode 100644
> > index 000000000000..ea66583fe74d
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> > @@ -0,0 +1,710 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
> > + *
> > + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
> > + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
> > + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "msm8998.dtsi"
> > +#include "pm8005.dtsi"
> > +#include "pm8998.dtsi"
> > +#include "pmi8998.dtsi"
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> > +
> > +/*
> > + * Delete following upstream (msm8998.dtsi) reserved
> > + * memory mappings which are different in this device.
> > + */
> > +/delete-node/ &adsp_mem;
> > +/delete-node/ &mpss_mem;
> > +/delete-node/ &venus_mem;
> > +/delete-node/ &mba_mem;
> > +/delete-node/ &slpi_mem;
> > +/delete-node/ &ipa_fw_mem;
> > +/delete-node/ &ipa_gsi_mem;
> > +/delete-node/ &gpu_mem;
> > +/delete-node/ &wlan_msa_mem;
> > +
> > +/ {
> > + model = "Xiaomi Mi 6";
> > + compatible = "xiaomi,sagit", "qcom,msm8998";
> > + chassis-type = "handset";
> > + /* Required for bootloader to select correct board */
> > + qcom,board-id = <30 0>;
> > +
> > + reserved-memory {
> > + /*
> > + * Xiaomi's ADSP firmware requires 30 MiB in total, so increase the adsp_mem
> > + * region by 4 MiB to account for this while relocating the other now
> > + * conflicting memory nodes accordingly.
> > + */
> > + adsp_mem: memory@8b200000 {
> > + reg = <0x0 0x8b200000 0x0 0x1e00000>;
> > + no-map;
> > + };
> > +
> > + mpss_mem: memory@8d000000 {
> > + reg = <0x0 0x8d000000 0x0 0x7000000>;
> > + no-map;
> > + };
> > +
> > + venus_mem: memory@94000000 {
> > + reg = <0x0 0x94000000 0x0 0x500000>;
> > + no-map;
> > + };
> > +
> > + mba_mem: memory@94500000 {
> > + reg = <0x0 0x94500000 0x0 0x200000>;
> > + no-map;
> > + };
> > +
> > + slpi_mem: memory@94700000 {
> > + reg = <0x0 0x94700000 0x0 0xf00000>;
> > + no-map;
> > + };
> > +
> > + ipa_fw_mem: memory@95600000 {
> > + reg = <0x0 0x95600000 0x0 0x10000>;
> > + no-map;
> > + };
> > +
> > + ipa_gsi_mem: memory@95610000 {
> > + reg = <0x0 0x95610000 0x0 0x5000>;
> > + no-map;
> > + };
> > +
> > + gpu_mem: memory@95615000 {
> > + reg = <0x0 0x95615000 0x0 0x100000>;
> > + no-map;
> > + };
> > +
> > + wlan_msa_mem: memory@95715000 {
> > + reg = <0x0 0x95715000 0x0 0x100000>;
> > + no-map;
> > + };
> > +
> > + /* Bootloader display framebuffer region */
> > + cont_splash_mem: memory@9d400000 {
> > + reg = <0x0 0x9d400000 0x0 0x2400000>;
> > + no-map;
> > + };
> > +
> > + /* For getting crash logs using Android downstream kernels */
> > + ramoops@ac000000 {
> > + compatible = "ramoops";
> > + reg = <0x0 0xac000000 0x0 0x200000>;
> > + console-size = <0x80000>;
> > + pmsg-size = <0x40000>;
> > + record-size = <0x8000>;
> > + ftrace-size = <0x20000>;
> > + };
> > +
> > + /*
> > + * The following memory regions on downstream are "dynamically allocated"
> > + * but given the same addresses every time. Hard code them as these addresses
> > + * are where the Xiaomi signed firmware expects them to be.
> > + */
> > + ipa_fws_region: memory@f7800000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x0 0xf7800000 0x0 0x5000>;
> > + no-map;
> > + };
> > +
> > + zap_shader_region: memory@f7900000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x0 0xf7900000 0x0 0x2000>;
> > + no-map;
> > + };
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + label = "Volume buttons";
> > + autorepeat;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vol_up_key_default>;
> > +
> > + key-vol-up {
> > + label = "Volume up";
> > + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_VOLUMEUP>;
> > + debounce-interval = <15>;
> > + wakeup-source;
> > + };
> > + };
> > +
> > + gpio-hall-sensor {
> > + compatible = "gpio-keys";
> > + label = "Hall effect sensor";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hall_sensor_default_state>;
> > +
> > + event-hall-sensor {
> > + label = "Hall Effect Sensor";
> > + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
> > + linux,input-type = <EV_SW>;
> > + linux,code = <SW_LID>;
> > + linux,can-disable;
> > + wakeup-source;
> > + };
> > + };
> > +
> > + vph_pwr: vph-pwr-regulator {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vph_pwr";
> > + regulator-min-microvolt = <3700000>;
> > + regulator-max-microvolt = <3700000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + disp_vddts_vreg: disp-vddts-regulator {
> > + compatible = "regulator-fixed";
> > + regulator-name = "disp-vddts-regulator";
> > + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-boot-on;
> > + };
> > +};
> > +
> > +&blsp1_i2c5 {
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > +
> > + touchscreen@20 {
> > + compatible = "syna,rmi4-i2c";
> > + reg = <0x20>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + interrupt-parent = <&tlmm>;
> > + interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
> > +
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&ts_active_state>;
> > + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
> > +
> > + vdd-supply = <&disp_vddts_vreg>;
> > + vio-supply = <&vreg_l6a_1p8>;
> > +
> > + syna,reset-delay-ms = <20>;
> > + syna,startup-delay-ms = <20>;
> > +
> > + rmi4-f01@1 {
> > + reg = <0x01>;
> > + syna,nosleep-mode = <1>;
> > + };
> > +
> > + rmi4-f12@12 {
> > + reg = <0x12>;
> > + touchscreen-x-mm = <64>;
> > + touchscreen-y-mm = <114>;
> > + syna,sensor-type = <1>;
> > + syna,rezero-wait-ms = <20>;
> > + };
> > +
> > + rmi4-f1a@1a {
> > + reg = <0x1a>;
> > + syna,codes = <KEY_BACK KEY_APPSELECT>;
> > + };
> > + };
> > +};
> > +
> > +&blsp1_i2c5_sleep {
> > + /delete-property/ bias-pull-up;
> > + bias-disable;
> > +};
> > +
> > +&blsp1_uart3 {
> > + status = "okay";
> > +
> > + bluetooth {
> > + compatible = "qcom,wcn3990-bt";
> > +
> > + vddio-supply = <&vreg_s4a_1p8>;
> > + vddxo-supply = <&vreg_l7a_1p8>;
> > + vddrf-supply = <&vreg_l17a_1p3>;
> > + vddch0-supply = <&vreg_l25a_3p3>;
> > + max-speed = <3200000>;
> > + };
> > +};
> > +
> > +&blsp1_uart3_on {
> > + rx {
>
> You need to rebase your changes. This won't work.
>
> If you test your DTS with dtbs_check, you will see the warnings.
>
>
>
> Best regards,
> Krzysztof
>

\
 
 \ /
  Last update: 2022-11-02 16:35    [W:0.046 / U:0.616 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site