lkml.org 
[lkml]   [2022]   [Oct]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [RESEND PATCH V2 6/9] cpufreq: amd_pstate: add AMD pstate EPP support for shared memory type processor
Date
[AMD Official Use Only - General]



> -----Original Message-----
> From: Huang, Ray <Ray.Huang@amd.com>
> Sent: Monday, October 17, 2022 6:55 PM
> To: Yuan, Perry <Perry.Yuan@amd.com>
> Cc: rafael.j.wysocki@intel.com; viresh.kumar@linaro.org; Sharma, Deepak
> <Deepak.Sharma@amd.com>; Limonciello, Mario
> <Mario.Limonciello@amd.com>; Fontenot, Nathan
> <Nathan.Fontenot@amd.com>; Deucher, Alexander
> <Alexander.Deucher@amd.com>; Huang, Shimmer
> <Shimmer.Huang@amd.com>; Du, Xiaojian <Xiaojian.Du@amd.com>; Meng,
> Li (Jassmine) <Li.Meng@amd.com>; linux-pm@vger.kernel.org; linux-
> kernel@vger.kernel.org
> Subject: Re: [RESEND PATCH V2 6/9] cpufreq: amd_pstate: add AMD pstate
> EPP support for shared memory type processor
>
> On Tue, Oct 11, 2022 at 12:22:45AM +0800, Yuan, Perry wrote:
> > Add Energy Performance Preference support for AMD SOCs which do not
> > contain a designated MSR for CPPC support. A shared memory interface
> > is used for CPPC on these SOCs and the ACPI PCC channel is used to
> > enable EPP and reset the desired performance.
> >
> > Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
> > ---
> > drivers/cpufreq/amd-pstate.c | 13 +++++++++++++
> > 1 file changed, 13 insertions(+)
> >
> > diff --git a/drivers/cpufreq/amd-pstate.c
> > b/drivers/cpufreq/amd-pstate.c index 2d28f458589c..08f9e335f97c 100644
> > --- a/drivers/cpufreq/amd-pstate.c
> > +++ b/drivers/cpufreq/amd-pstate.c
> > @@ -135,12 +135,25 @@ static inline int pstate_enable(bool enable)
> >
> > static int cppc_enable(bool enable)
> > {
> > + struct cppc_perf_ctrls perf_ctrls;
> > int cpu, ret = 0;
> >
> > for_each_present_cpu(cpu) {
> > ret = cppc_set_enable(cpu, enable);
> > if (ret)
> > return ret;
> > + if (epp) {
> > + /* Enable autonomous mode for EPP */
> > + ret = cppc_set_auto_epp(cpu, enable);
> > + if (ret)
> > + return ret;
> > +
> > + /* Set desired perf as zero to allow EPP firmware
> control */
> > + perf_ctrls.desired_perf = 0;
> > + ret = cppc_set_perf(cpu, &perf_ctrls);
> > + if (ret)
> > + return ret;
> > + }
>
> This patch only writes the desired_perf as 0 to enable the EPP function, but it
> cannot be an independent function or patch without the dependency of the
> next one (patch 7).
>
> Thanks,
> Ray

Do you mean that I could squash this patch into Patch 7 ?
If so , I will get this into V3.

Perry.

\
 
 \ /
  Last update: 2022-10-20 18:05    [W:0.076 / U:2.228 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site