lkml.org 
[lkml]   [2022]   [Jan]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 15/20] i2c: cht-wc: Make charger i2c-client instantiation board/device-model specific
On Sun, Jan 30, 2022 at 09:45:52PM +0100, Hans de Goede wrote:
> The i2c-controller on the Cherry Trail - Whiskey Cove PMIC is special
> in that it is always connected to the I2C charger IC of the board on
> which the PMIC is used; and the charger IC is not described in ACPI,
> so the i2c-cht-wc code needs to instantiate an i2c-client for it itself.
>
> So far this was hardcoded to instantiate an i2c-client for the
> bq24292i, with all properties, etc. set to match how this charger
> is used on the GPD win and GPD pocket devices.
>
> There is a rudimentary check to make sure the ACPI tables are at least
> somewhat as expected, but this is far from accurate, leading to
> a wrong i2c-client being instantiated for the charger on some boards.
>
> Switch to the new DMI based intel_cht_wc_get_model() helper which is
> exported by the MFD driver for the CHT Whiskey Cove PMIC to help PMIC
> cell drivers like the i2c-cht-wc code reliably detect which board
> they are running on.
>
> And add board_info for the charger ICs as found on the other 2 known
> boards with a Whisky Cove PMIC.
>
> This has been tested on all 3 known boards.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

> Acked-by: Wolfram Sang <wsa@kernel.org>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v3:
> - Add Wolfram's Ack for taking this upstream through another tree
> then the i2c tree
> - Some minor tweaks / spelling fixes based on Andy's review
> ---
> drivers/i2c/busses/i2c-cht-wc.c | 120 +++++++++++++++++++++++++++-----
> 1 file changed, 102 insertions(+), 18 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-cht-wc.c b/drivers/i2c/busses/i2c-cht-wc.c
> index 1cf68f85b2e1..54e909f9eab6 100644
> --- a/drivers/i2c/busses/i2c-cht-wc.c
> +++ b/drivers/i2c/busses/i2c-cht-wc.c
> @@ -18,6 +18,7 @@
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/power/bq24190_charger.h>
> +#include <linux/power/bq25890_charger.h>
> #include <linux/slab.h>
>
> #define CHT_WC_I2C_CTRL 0x5e24
> @@ -270,6 +271,7 @@ static const struct irq_chip cht_wc_i2c_irq_chip = {
> .name = "cht_wc_ext_chrg_irq_chip",
> };
>
> +/********** GPD Win / Pocket charger IC settings **********/
> static const char * const bq24190_suppliers[] = {
> "tcpm-source-psy-i2c-fusb302" };
>
> @@ -304,17 +306,92 @@ static struct bq24190_platform_data bq24190_pdata = {
> .regulator_init_data = &bq24190_vbus_init_data,
> };
>
> +static struct i2c_board_info gpd_win_board_info = {
> + .type = "bq24190",
> + .addr = 0x6b,
> + .dev_name = "bq24190",
> + .swnode = &bq24190_node,
> + .platform_data = &bq24190_pdata,
> +};
> +
> +/********** Xiaomi Mi Pad 2 charger IC settings **********/
> +static struct regulator_consumer_supply bq2589x_vbus_consumer = {
> + .supply = "vbus",
> + .dev_name = "cht_wcove_pwrsrc",
> +};
> +
> +static const struct regulator_init_data bq2589x_vbus_init_data = {
> + .constraints = {
> + .valid_ops_mask = REGULATOR_CHANGE_STATUS,
> + },
> + .consumer_supplies = &bq2589x_vbus_consumer,
> + .num_consumer_supplies = 1,
> +};
> +
> +static struct bq25890_platform_data bq2589x_pdata = {
> + .regulator_init_data = &bq2589x_vbus_init_data,
> +};
> +
> +static const struct property_entry xiaomi_mipad2_props[] = {
> + PROPERTY_ENTRY_BOOL("linux,skip-reset"),
> + PROPERTY_ENTRY_BOOL("linux,read-back-settings"),
> + { }
> +};
> +
> +static const struct software_node xiaomi_mipad2_node = {
> + .properties = xiaomi_mipad2_props,
> +};
> +
> +static struct i2c_board_info xiaomi_mipad2_board_info = {
> + .type = "bq25890",
> + .addr = 0x6a,
> + .dev_name = "bq25890",
> + .swnode = &xiaomi_mipad2_node,
> + .platform_data = &bq2589x_pdata,
> +};
> +
> +/********** Lenovo Yogabook YB1-X90F/-X91F/-X91L charger settings **********/
> +static const char * const lenovo_yb1_bq25892_suppliers[] = { "cht_wcove_pwrsrc" };
> +
> +static const struct property_entry lenovo_yb1_bq25892_props[] = {
> + PROPERTY_ENTRY_STRING_ARRAY("supplied-from",
> + lenovo_yb1_bq25892_suppliers),
> + PROPERTY_ENTRY_U32("linux,pump-express-vbus-max", 12000000),
> + PROPERTY_ENTRY_BOOL("linux,skip-reset"),
> + /*
> + * The firmware sets everything to the defaults, which leads to a
> + * somewhat low charge-current of 2048mA and worse to a battery-voltage
> + * of 4.2V instead of 4.35V (when booted without a charger connected).
> + * Use our own values instead of "linux,read-back-settings" to fix this.
> + */
> + PROPERTY_ENTRY_U32("ti,charge-current", 4224000),
> + PROPERTY_ENTRY_U32("ti,battery-regulation-voltage", 4352000),
> + PROPERTY_ENTRY_U32("ti,termination-current", 256000),
> + PROPERTY_ENTRY_U32("ti,precharge-current", 128000),
> + PROPERTY_ENTRY_U32("ti,minimum-sys-voltage", 3500000),
> + PROPERTY_ENTRY_U32("ti,boost-voltage", 4998000),
> + PROPERTY_ENTRY_U32("ti,boost-max-current", 1400000),
> + PROPERTY_ENTRY_BOOL("ti,use-ilim-pin"),
> + { }
> +};
> +
> +static const struct software_node lenovo_yb1_bq25892_node = {
> + .properties = lenovo_yb1_bq25892_props,
> +};
> +
> +static struct i2c_board_info lenovo_yogabook1_board_info = {
> + .type = "bq25892",
> + .addr = 0x6b,
> + .dev_name = "bq25892",
> + .swnode = &lenovo_yb1_bq25892_node,
> + .platform_data = &bq2589x_pdata,
> +};
> +
> static int cht_wc_i2c_adap_i2c_probe(struct platform_device *pdev)
> {
> struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
> + struct i2c_board_info *board_info = NULL;
> struct cht_wc_i2c_adap *adap;
> - struct i2c_board_info board_info = {
> - .type = "bq24190",
> - .addr = 0x6b,
> - .dev_name = "bq24190",
> - .swnode = &bq24190_node,
> - .platform_data = &bq24190_pdata,
> - };
> int ret, reg, irq;
>
> irq = platform_get_irq(pdev, 0);
> @@ -379,17 +456,24 @@ static int cht_wc_i2c_adap_i2c_probe(struct platform_device *pdev)
> if (ret)
> goto remove_irq_domain;
>
> - /*
> - * Normally the Whiskey Cove PMIC is paired with a TI bq24292i charger,
> - * connected to this i2c bus, and a max17047 fuel-gauge and a fusb302
> - * USB Type-C controller connected to another i2c bus. In this setup
> - * the max17047 and fusb302 devices are enumerated through an INT33FE
> - * ACPI device. If this device is present register an i2c-client for
> - * the TI bq24292i charger.
> - */
> - if (acpi_dev_present("INT33FE", NULL, -1)) {
> - board_info.irq = adap->client_irq;
> - adap->client = i2c_new_client_device(&adap->adapter, &board_info);
> + switch (pmic->cht_wc_model) {
> + case INTEL_CHT_WC_GPD_WIN_POCKET:
> + board_info = &gpd_win_board_info;
> + break;
> + case INTEL_CHT_WC_XIAOMI_MIPAD2:
> + board_info = &xiaomi_mipad2_board_info;
> + break;
> + case INTEL_CHT_WC_LENOVO_YOGABOOK1:
> + board_info = &lenovo_yogabook1_board_info;
> + break;
> + default:
> + dev_warn(&pdev->dev, "Unknown model, not instantiating charger device\n");
> + break;
> + }
> +
> + if (board_info) {
> + board_info->irq = adap->client_irq;
> + adap->client = i2c_new_client_device(&adap->adapter, board_info);
> if (IS_ERR(adap->client)) {
> ret = PTR_ERR(adap->client);
> goto del_adapter;
> --
> 2.33.1
>

--
With Best Regards,
Andy Shevchenko


\
 
 \ /
  Last update: 2022-01-31 14:52    [W:0.142 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site