lkml.org 
[lkml]   [2021]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next 4/4] net: bcmgenet: add support for ethtool flow control
On Sat, Sep 25, 2021 at 08:21:14PM -0700, Florian Fainelli wrote:
> From: Doug Berger <opendmb@gmail.com>
>
> This commit extends the supported ethtool operations to allow MAC
> level flow control to be configured for the bcmgenet driver.
>
> The ethtool utility can be used to change the configuration of
> auto-negotiated symmetric and asymmetric modes as well as manually
> configuring support for RX and TX Pause frames individually.
>
> Signed-off-by: Doug Berger <opendmb@gmail.com>
> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
> ---
> .../net/ethernet/broadcom/genet/bcmgenet.c | 51 +++++++++++++++++++
> .../net/ethernet/broadcom/genet/bcmgenet.h | 4 ++
> drivers/net/ethernet/broadcom/genet/bcmmii.c | 44 +++++++++++++---
> 3 files changed, 92 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
> index 3427f9ed7eb9..6a8234bc9428 100644
> --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
> +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
> @@ -935,6 +935,48 @@ static int bcmgenet_set_coalesce(struct net_device *dev,
> return 0;
> }
>
> +static void bcmgenet_get_pauseparam(struct net_device *dev,
> + struct ethtool_pauseparam *epause)
> +{
> + struct bcmgenet_priv *priv;
> + u32 umac_cmd;
> +
> + priv = netdev_priv(dev);
> +
> + epause->autoneg = priv->autoneg_pause;
> +
> + if (netif_carrier_ok(dev)) {
> + /* report active state when link is up */
> + umac_cmd = bcmgenet_umac_readl(priv, UMAC_CMD);
> + epause->tx_pause = !(umac_cmd & CMD_TX_PAUSE_IGNORE);
> + epause->rx_pause = !(umac_cmd & CMD_RX_PAUSE_IGNORE);
> + } else {
> + /* otherwise report stored settings */
> + epause->tx_pause = priv->tx_pause;
> + epause->rx_pause = priv->rx_pause;
> + }
> +}
> +
> +static int bcmgenet_set_pauseparam(struct net_device *dev,
> + struct ethtool_pauseparam *epause)
> +{
> + struct bcmgenet_priv *priv = netdev_priv(dev);
> +
> + if (!dev->phydev)
> + return -ENODEV;
> +
> + if (!phy_validate_pause(dev->phydev, epause))
> + return -EINVAL;
> +
> + priv->autoneg_pause = !!epause->autoneg;
> + priv->tx_pause = !!epause->tx_pause;
> + priv->rx_pause = !!epause->rx_pause;
> +
> + bcmgenet_phy_pause_set(dev, priv->rx_pause, priv->tx_pause);

I don't think this is correct. If epause->autoneg is false, you
probably want to pass false, false here, so that the PHY will not
announce any modes. And then call bcmgenet_mac_config() to set the
manual pause bits. But watch out that you don't hold the PHY lock, so
you should not access any phydev members.

> + } else {
> + /* pause capability defaults to Symmetric */
> + if (priv->autoneg_pause) {
> + bool tx_pause = 0, rx_pause = 0;
> +
> + if (phydev->autoneg)
> + phy_get_pause(phydev, &tx_pause, &rx_pause);
>
> - /* pause capability */
> - if (!phydev->pause)
> - cmd_bits |= CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE;
> + if (!tx_pause)
> + cmd_bits |= CMD_TX_PAUSE_IGNORE;
> + if (!rx_pause)
> + cmd_bits |= CMD_RX_PAUSE_IGNORE;
> + }

Looks like there should be an else here?

> +
> + /* Manual override */
> + if (!priv->rx_pause)
> + cmd_bits |= CMD_RX_PAUSE_IGNORE;
> + if (!priv->tx_pause)
> + cmd_bits |= CMD_TX_PAUSE_IGNORE;
> + }
>
> /* Program UMAC and RGMII block based on established
> * link speed, duplex, and pause. The speed set in
> @@ -101,6 +118,21 @@ static int bcmgenet_fixed_phy_link_update(struct net_device *dev,
> return 0;
> }
>
> +void bcmgenet_phy_pause_set(struct net_device *dev, bool rx, bool tx)
> +{
> + struct phy_device *phydev = dev->phydev;
> +
> + linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->advertising, rx);
> + linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->advertising,
> + rx | tx);
> + phy_start_aneg(phydev);
> +
> + mutex_lock(&phydev->lock);
> + if (phydev->link)
> + bcmgenet_mac_config(dev);
> + mutex_unlock(&phydev->lock);

It is a bit oddly named, but phy_set_asym_pause() does this, minus the
lock. Please use that, rather than open coding this.

Locking is something i'm looking at now. I'm trying to go through all
the phylib calls the MAC use and checking if locks need to be added.

Andrew

\
 
 \ /
  Last update: 2021-09-26 16:28    [W:0.084 / U:0.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site