Messages in this thread | | | From | David Stevens <> | Subject | [PATCH v2 0/9] Add dynamic iommu backed bounce buffers | Date | Fri, 6 Aug 2021 19:34:14 +0900 |
| |
From: David Stevens <stevensd@chromium.org>
This patch series adds support for per-domain dynamic pools of iommu bounce buffers to the dma-iommu API. This allows iommu mappings to be reused while still maintaining strict iommu protection.
This bounce buffer support is used to add a new config option that, when enabled, causes all non-direct streaming mappings below a configurable size to go through the bounce buffers. This serves as an optimization on systems where manipulating iommu mappings is very expensive. For example, virtio-iommu operations in a guest on a linux host require a vmexit, involvement the VMM, and a VFIO syscall. For relatively small DMA operations, memcpy can be significantly faster.
As a performance comparison, on a device with an i5-10210U, I ran fio with a VFIO passthrough NVMe drive and virtio-iommu with '--direct=1 --rw=read --ioengine=libaio --iodepth=64' and block sizes 4k, 16k, 64k, and 128k. Test throughput increased by 2.8x, 4.7x, 3.6x, and 3.6x. Time spent in iommu_dma_unmap_(page|sg) per GB processed decreased by 97%, 94%, 90%, and 87%. Time spent in iommu_dma_map_(page|sg) decreased by >99%, as bounce buffers don't require syncing here in the read case. Running with multiple jobs doesn't serve as a useful performance comparison because virtio-iommu and vfio_iommu_type1 both have big locks that significantly limit mulithreaded DMA performance.
These pooled bounce buffers are also used for subgranule mappings with untrusted devices, replacing the single use bounce buffers used currently. The biggest difference here is that the new implementation maps a whole sglist using a single bounce buffer. The new implementation does not support using bounce buffers for only some segments of the sglist, so it may require more copying. However, the current implementation requires per-segment iommu map/unmap operations for all untrusted sglist mappings (fully aligned sglists included). On a i5-10210U laptop with the internal NVMe drive made to appear untrusted, fio --direct=1 --rw=read --ioengine=libaio --iodepth=64 --bs=64k showed a statistically significant decrease in CPU load from 2.28% -> 2.17% with the new iommu bounce buffer optimization enabled.
Each domain's buffer pool is split into multiple power-of-2 size classes. Each class allocates a fixed number of buffer slot metadata. A large iova range is allocated, and each slot is assigned an iova from the range. This allows the iova to be easily mapped back to the slot, and allows the critical section of most pool operations to be constant time. The one exception is finding a cached buffer to reuse. These are only separated according to R/W permissions - the use of other permissions such as IOMMU_PRIV may require a linear search through the cache. However, these other permissions are rare and likely exhibit high locality, so the should not be a bottleneck in practice.
Since untrusted devices may require bounce buffers, each domain has a fallback rbtree to manage single use buffers. This may be necessary if a very large number of DMA operations are simultaneously in-flight, or for very large individual DMA operations.
This patch set does not use swiotlb. There are two primary ways in which swiotlb isn't compatible with per-domain buffer pools. First, swiotlb allocates buffers to be compatible with a single device, whereas per-domain buffer pools don't handle that during buffer allocation as a single buffer may end up being used by multiple devices. Second, swiotlb allocation establishes the original to bounce buffer mapping, which again doesn't work if buffers can be reused. Effectively the only code that can be shared between the two use cases is allocating slots from the swiotlb's memory. However, given that we're going to be allocating memory for use with an iommu, allocating memory from a block of memory explicitly set aside to deal with a lack of iommu seems kind of contradictory. At best there might be a small performance improvement if wiotlb allocation is faster than regular page allocation, but buffer allocation isn't on the hot path anyway.
Not using the swiotlb has the benefit that memory doesn't have to be preallocated. Instead, bounce buffers consume memory only for in-flight dma transactions (ignoring temporarily cached buffers), which is the smallest amount possible. This makes it easier to use bounce buffers as an optimization on systems with large numbers of devices or in situations where devices are unknown, since it is not necessary to try to tune how much memory needs to be set aside to achieve good performance without costing too much memory.
Finally, this series adds a new DMA_ATTR_PERSISTENT_STREAMING flag. This is meant to address devices which create long lived streaming mappings but manage CPU cache coherency without using the dma_sync_* APIs. Currently, these devices don't function properly with swiotlb=force. The new flag is used to bypass bounce buffers so such devices will function when the new bounce buffer optimization is enabled. The flag is added to the i915 driver, which creates such mappings. It can also be added to various dma-buf implementations as an optimization, although that is not done here.
v1 -> v2: - Replace existing untrusted bounce buffers with new bounce buffer pools. This includes significant rework to account for untrusted bounce buffers being required instead of an optimization. - Add flag for persistent streaming mappings.
David Stevens (9): Revert "iommu: Allow the dma-iommu api to use bounce buffers" dma-iommu: expose a few helper functions to module dma-iommu: bounce buffers for untrusted devices dma-iommu: remove extra buffer search on unmap dma-iommu: clear only necessary bytes dma-iommu: add bounce buffer pools dma-iommu: support iommu bounce buffer optimization dma-mapping: add persistent streaming mapping flag drm/i915: use DMA_ATTR_PERSISTENT_STREAMING flag
drivers/gpu/drm/i915/gem/i915_gem_dmabuf.c | 4 +- drivers/gpu/drm/i915/i915_gem_gtt.c | 3 +- drivers/iommu/Kconfig | 11 + drivers/iommu/Makefile | 2 +- drivers/iommu/dma-iommu.c | 268 ++++----- drivers/iommu/io-bounce-buffers.c | 533 +++++++++++++++++ drivers/iommu/io-bounce-buffers.h | 49 ++ drivers/iommu/io-buffer-manager.c | 633 +++++++++++++++++++++ drivers/iommu/io-buffer-manager.h | 94 +++ include/linux/dma-iommu.h | 12 + include/linux/dma-mapping.h | 11 + 11 files changed, 1460 insertions(+), 160 deletions(-) create mode 100644 drivers/iommu/io-bounce-buffers.c create mode 100644 drivers/iommu/io-bounce-buffers.h create mode 100644 drivers/iommu/io-buffer-manager.c create mode 100644 drivers/iommu/io-buffer-manager.h
-- 2.32.0.605.g8dce9f2422-goog
| |