lkml.org 
[lkml]   [2021]   [Apr]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] net: phy: fix PHY possibly unwork after MDIO bus resume back
Date

Hi Heiner,

> -----Original Message-----
> From: Heiner Kallweit <hkallweit1@gmail.com>
> Sent: 2021年4月5日 6:49
> To: Joakim Zhang <qiangqing.zhang@nxp.com>; andrew@lunn.ch;
> linux@armlinux.org.uk; davem@davemloft.net; kuba@kernel.org
> Cc: netdev@vger.kernel.org; linux-kernel@vger.kernel.org; dl-linux-imx
> <linux-imx@nxp.com>; christian.melki@t2data.com
> Subject: Re: [PATCH] net: phy: fix PHY possibly unwork after MDIO bus resume
> back
>
> On 04.04.2021 16:09, Heiner Kallweit wrote:
> > On 04.04.2021 12:07, Joakim Zhang wrote:
> >> commit 4c0d2e96ba055 ("net: phy: consider that suspend2ram may cut
> >> off PHY power") invokes phy_init_hw() when MDIO bus resume, it will
> >> soft reset PHY if PHY driver implements soft_reset callback.
> >> commit 764d31cacfe4 ("net: phy: micrel: set soft_reset callback to
> >> genphy_soft_reset for KSZ8081") adds soft_reset for KSZ8081. After
> >> these two patches, I found i.MX6UL 14x14 EVK which connected to
> >> KSZ8081RNB doesn't work any more when system resume back, MAC driver
> is fec_main.c.
> >>
> >> It's obvious that initializing PHY hardware when MDIO bus resume back
> >> would introduce some regression when PHY implements soft_reset. When
> >> I
> >
> > Why is this obvious? Please elaborate on why a soft reset should break
> > something.
> >
> >> am debugging, I found PHY works fine if MAC doesn't support
> >> suspend/resume or phy_stop()/phy_start() doesn't been called during
> >> suspend/resume. This let me realize, PHY state machine
> >> phy_state_machine() could do something breaks the PHY.
> >>
> >> As we known, MAC resume first and then MDIO bus resume when system
> >> resume back from suspend. When MAC resume, usually it will invoke
> >> phy_start() where to change PHY state to PHY_UP, then trigger the
> >> stat> machine to run now. In phy_state_machine(), it will
> >> start/config auto-nego, then change PHY state to PHY_NOLINK, what to
> >> next is periodically check PHY link status. When MDIO bus resume, it
> >> will initialize PHY hardware, including soft_reset, what would
> >> soft_reset affect seems various from different PHYs. For KSZ8081RNB,
> >> when it in PHY_NOLINK state and then perform a soft reset, it will never
> complete auto-nego.
> >
> > Why? That would need to be checked in detail. Maybe chip errata
> > documentation provides a hint.
> >
>
> The KSZ8081 spec says the following about bit BMCR_PDOWN:
>
> If software reset (Register 0.15) is
> used to exit power-down mode
> (Register 0.11 = 1), two software
> reset writes (Register 0.15 = 1) are
> required. The first write clears
> power-down mode; the second
> write resets the chip and re-latches
> the pin strapping pin values.
>
> Maybe this causes the issue you see and genphy_soft_reset() isn't appropriate
> for this PHY. Please re-test with the KSZ8081 soft reset following the spec
> comment.

Yes, I also noticed this note in spec, and tried to soft reset twice from PHY driver, but still can't work.

What is strange is that, ifup/ifdown can work fine, which is almost the same route with suspend/resume,
except suspend/resume has state machine running.

>
> >>
> >> This patch changes PHY state to PHY_UP when MDIO bus resume back, it
> >> should be reasonable after PHY hardware re-initialized. Also give
> >> state machine a chance to start/config auto-nego again.
> >>
> >
> > If the MAC driver calls phy_stop() on suspend, then phydev->suspended
> > is true and mdio_bus_phy_may_suspend() returns false. As a consequence
> > phydev->suspended_by_mdio_bus is false and mdio_bus_phy_resume()
> > skips the PHY hw initialization.
> > Please also note that mdio_bus_phy_suspend() calls phy_stop_machine()
> > that sets the state to PHY_UP.
> >
>
> Forgot that MDIO bus suspend is done before MAC driver suspend.
> Therefore disregard this part for now.

OK.

Best Regards,
Joakim Zhang
> > Having said that the current argumentation isn't convincing. I'm not
> > aware of such issues on other systems, therefore it's likely that
> > something is system-dependent.
> >
> > Please check the exact call sequence on your system, maybe it provides
> > a hint.
> >
> >> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
> >> ---
> >> drivers/net/phy/phy_device.c | 7 +++++++
> >> 1 file changed, 7 insertions(+)
> >>
> >> diff --git a/drivers/net/phy/phy_device.c
> >> b/drivers/net/phy/phy_device.c index cc38e326405a..312a6f662481
> >> 100644
> >> --- a/drivers/net/phy/phy_device.c
> >> +++ b/drivers/net/phy/phy_device.c
> >> @@ -306,6 +306,13 @@ static __maybe_unused int
> mdio_bus_phy_resume(struct device *dev)
> >> ret = phy_resume(phydev);
> >> if (ret < 0)
> >> return ret;
> >> +
> >> + /* PHY state could be changed to PHY_NOLINK from MAC controller
> resume
> >> + * rounte with phy_start(), here change to PHY_UP after re-initializing
> >> + * PHY hardware, let PHY state machine to start/config auto-nego again.
> >> + */
> >> + phydev->state = PHY_UP;
> >> +
> >> no_resume:
> >> if (phydev->attached_dev && phydev->adjust_link)
> >> phy_start_machine(phydev);
> >>
> >

\
 
 \ /
  Last update: 2021-04-06 03:40    [W:0.077 / U:0.796 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site