lkml.org 
[lkml]   [2021]   [Feb]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: dts: stm32: fix usart 2 & 3 pinconf to wake up with flow control
Date
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.

Fixes: 842ed898a757 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")

Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 21 ++++++++++++++++++---
1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 7b4249ed1983..060baa8b7e9d 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1891,10 +1891,15 @@
usart2_idle_pins_c: usart2-idle-2 {
pins1 {
pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
- <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
<STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
bias-disable;
};
@@ -1940,10 +1945,15 @@
usart3_idle_pins_b: usart3-idle-1 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
- <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
<STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
bias-disable;
};
@@ -1976,10 +1986,15 @@
usart3_idle_pins_c: usart3-idle-2 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
- <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
<STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
bias-disable;
};
--
2.17.1
\
 
 \ /
  Last update: 2021-02-11 12:39    [W:0.033 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site